How Much Recycled Concrete Aggregate for a 10x16 Shed Base?
A 10 by 16 foot shed base is 160 square feet. How much recycled concrete aggregate for a 10x16 shed base depends on depth: at 4 inches it is about 1.98 cubic yards or 2.6 tons. Suppliers usually sell by the ton, so the tonnage is the number to give them.
Volume and tonnage calculator →The math for a 10x16 shed base
- Area: 10 × 16 = 160 sq ft.
- Depth in feet: 4 ÷ 12 = 0.333 ft.
- Cubic feet: 160 × 0.333 = 53.3 cu ft.
- Cubic yards: ÷ 27 = 1.98 yd³.
- Tons: × 1.3 = 2.6 tons.
The volume and tonnage calculator does this for any size.
Recycled concrete aggregate needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 3 in | 1.48 | 1.9 | 2.1 |
| 4 in | 1.98 | 2.6 | 2.8 |
| 6 in | 2.96 | 3.9 | 4.2 |
About recycled concrete aggregate
Ask whether the recycled concrete has been screened for rebar and debris. Fresh-crushed concrete can also be alkaline, so keep it away from sensitive plantings and streams. Weight per yard is a planning number; the scale ticket at the yard is the real one.
Preparing the shed base
Level the footprint, extend the stone a foot or so beyond the shed walls for drip and drainage, and compact in lifts. A timber or block border holds the pad shape. This shed base sees a shed floor frame, so match the depth to that load rather than to the minimum.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 2.8 tons fits in a single typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the shed base as firm ground allows.
Good and poor uses for recycled concrete aggregate
Good uses:
- Driveway and pad bases
- Temporary construction entrances
- Fill under slabs when compacted in lifts
Think twice for:
- Near ponds, streams or sensitive plants, since fresh crush can raise pH
- Decorative top layers
- Drainage layers, unless the product is clean and screened
Quick reference numbers
- Per inch over 100 sq ft: about 0.40 tons of recycled concrete aggregate (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.0 tons.
- Another size for comparison: a 8x16 area at 3 inches takes about 1.5 tons.
- Weight used here: about 1.3 tons per cubic yard.
Mistakes that throw off the order
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
Questions people ask
How many tons of recycled concrete aggregate for a 10x16 shed base?
About 2.6 tons at 4 inches deep, or 2.8 tons with 10 percent extra.
How many cubic yards is a 10x16 shed base at 4 inches?
About 1.98 cubic yards.
How much does a cubic yard of recycled concrete aggregate weigh?
Usually around 1.2 to 1.4 tons, depending on stone size, fines and moisture.
How deep should recycled concrete aggregate be for a shed base?
The table above shows 3 to 6 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 10x16?
160 square feet.
Related guides
- Crushed Stone vs Gravel: Differences and Best Uses
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much Recycled Concrete Aggregate for a 10x12 Shed Base?
- How Much Recycled Concrete Aggregate for a 10x14 Shed Base?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.