How Much Recycled Concrete Aggregate for a 10x80 Driveway?
How much recycled concrete aggregate for a 10x80 driveway: at 4 inches deep you need about 9.88 cubic yards, which is roughly 12.8 tons at 1.3 tons per yard. The driveway covers 800 square feet, so every inch of depth adds about 2.47 yards.
Volume and tonnage calculator →The math for a 10x80 driveway
- Area: 10 × 80 = 800 sq ft.
- Depth in feet: 4 ÷ 12 = 0.333 ft.
- Cubic feet: 800 × 0.333 = 266.7 cu ft.
- Cubic yards: ÷ 27 = 9.88 yd³.
- Tons: × 1.3 = 12.8 tons.
The volume and tonnage calculator does this for any size.
Recycled concrete aggregate needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 3 in | 7.41 | 9.6 | 10.6 |
| 4 in | 9.88 | 12.8 | 14.1 |
| 6 in | 14.81 | 19.3 | 21.2 |
About recycled concrete aggregate
Ask whether the recycled concrete has been screened for rebar and debris. Fresh-crushed concrete can also be alkaline, so keep it away from sensitive plantings and streams. Weight per yard is a planning number; the scale ticket at the yard is the real one.
Preparing the driveway
Strip sod and soft topsoil, grade for drainage and compact the subgrade before any stone goes down. Gravel drives last longer with a compacted base layer under the top stone and a slight crown so water runs off. For car and truck traffic, the depths in the table above are a reasonable starting range.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 14.1 tons may take more than one typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the driveway as firm ground allows.
Where recycled concrete aggregate fits
Works well for:
- Driveway and pad bases
- Temporary construction entrances
- Fill under slabs when compacted in lifts
Think twice for:
- Near ponds, streams or sensitive plants, since fresh crush can raise pH
- Decorative top layers
- Drainage layers, unless the product is clean and screened
Quick reference numbers
- Per inch over 100 sq ft: about 0.40 tons of recycled concrete aggregate (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.0 tons.
- Another size for comparison: a 15x30 area at 3 inches takes about 5.4 tons.
- Weight used here: about 1.3 tons per cubic yard.
Common estimating mistakes
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
Questions people ask
How many tons of recycled concrete aggregate for a 10x80 driveway?
About 12.8 tons at 4 inches deep, or 14.1 tons with 10 percent extra.
How many cubic yards is a 10x80 driveway at 4 inches?
About 9.88 cubic yards.
How much does a cubic yard of recycled concrete aggregate weigh?
Usually around 1.2 to 1.4 tons, depending on stone size, fines and moisture.
How deep should recycled concrete aggregate be for a driveway?
The table above shows 3 to 6 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 10x80?
800 square feet.
Related guides
- Crushed Stone vs Gravel: Differences and Best Uses
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much Recycled Concrete Aggregate for a 10x70 Driveway?
- How Much Recycled Concrete Aggregate for a 10x75 Driveway?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.