How Much River Rock for a 20x12 Patio?
How much river rock for a 20x12 patio: at 3 inches deep you need about 2.22 cubic yards, which is roughly 3.0 tons at 1.35 tons per yard. The patio covers 240 square feet, so every inch of depth adds about 0.74 yards.
Volume and tonnage calculator →The math for a 20x12 patio
- Area: 20 × 12 = 240 sq ft.
- Depth in feet: 3 ÷ 12 = 0.250 ft.
- Cubic feet: 240 × 0.250 = 60.0 cu ft.
- Cubic yards: ÷ 27 = 2.22 yd³.
- Tons: × 1.35 = 3.0 tons.
The volume and tonnage calculator does this for any size.
River rock needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 2 in | 1.48 | 2.0 | 2.2 |
| 3 in | 2.22 | 3.0 | 3.3 |
| 4 in | 2.96 | 4.0 | 4.4 |
About river rock
River rock is smooth, water-worn stone sold in sizes from about 3/4 inch to several inches. Larger sizes cover fewer square feet per ton at the same depth because the voids between stones are bigger. Weight per yard is a planning number; the scale ticket at the yard is the real one.
Preparing the patio
Remove sod, level the area with a slight slope away from the house, and lay landscape fabric if weeds are a concern. Edging keeps loose material inside the patio footprint. Since the patio carries foot traffic and furniture, a little extra depth is cheap insurance.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 3.3 tons fits in a single typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the patio as firm ground allows.
When to choose river rock
Best suited to:
- Dry creek beds and drainage swales
- Decorative borders and planting beds
- Around downspouts to stop splash erosion
Poor fit for:
- Walking surfaces
- Driveways
- Bases under slabs or pavers
Quick reference numbers
- Per inch over 100 sq ft: about 0.42 tons of river rock (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.2 tons.
- Another size for comparison: a 10x20 area at 2 inches takes about 1.7 tons.
- Weight used here: about 1.35 tons per cubic yard.
Where estimates go wrong
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
Questions people ask
How many tons of river rock for a 20x12 patio?
About 3.0 tons at 3 inches deep, or 3.3 tons with 10 percent extra.
How many cubic yards is a 20x12 patio at 3 inches?
About 2.22 cubic yards.
How much does a cubic yard of river rock weigh?
Usually around 1.25 to 1.45 tons, depending on stone size, fines and moisture.
How deep should river rock be for a patio?
The table above shows 2 to 4 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 20x12?
240 square feet.
Related guides
- How Much Does a Ton of River Rock Cover?
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much River Rock for a 16x30 Patio?
- How Much River Rock for a 20x10 Patio?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.