How Much River Rock for a 4x75 Walkway?
How much river rock for a 4x75 walkway is a quick volume problem. 300 square feet at 3 inches comes to 2.78 cubic yards. River rock usually weighs about 1.25 to 1.45 tons per cubic yard, so plan on roughly 3.8 tons.
Volume and tonnage calculator →The math for a 4x75 walkway
- Area: 4 × 75 = 300 sq ft.
- Depth in feet: 3 ÷ 12 = 0.250 ft.
- Cubic feet: 300 × 0.250 = 75.0 cu ft.
- Cubic yards: ÷ 27 = 2.78 yd³.
- Tons: × 1.35 = 3.8 tons.
The volume and tonnage calculator does this for any size.
River rock needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 2 in | 1.85 | 2.5 | 2.8 |
| 3 in | 2.78 | 3.8 | 4.1 |
| 4 in | 3.70 | 5.0 | 5.5 |
About river rock
River rock is smooth, water-worn stone sold in sizes from about 3/4 inch to several inches. Larger sizes cover fewer square feet per ton at the same depth because the voids between stones are bigger. If the yard sells by the cubic yard instead of the ton, use the cubic-yard column directly.
Preparing the walkway
Dig the path a few inches below grade, compact the bottom, add fabric if needed and install edging on both sides so the material stays on the walk. For foot traffic, the depths in the table above are a reasonable starting range.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 4.1 tons fits in a single typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the walkway as firm ground allows.
Where river rock fits
Works well for:
- Dry creek beds and drainage swales
- Decorative borders and planting beds
- Around downspouts to stop splash erosion
Less suited to:
- Walking surfaces
- Driveways
- Bases under slabs or pavers
Quick reference numbers
- Per inch over 100 sq ft: about 0.42 tons of river rock (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.2 tons.
- Another size for comparison: a 8x16 area at 4 inches takes about 2.1 tons.
- Weight used here: about 1.35 tons per cubic yard.
Where estimates go wrong
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
Questions people ask
How many tons of river rock for a 4x75 walkway?
About 3.8 tons at 3 inches deep, or 4.1 tons with 10 percent extra.
How many cubic yards is a 4x75 walkway at 3 inches?
About 2.78 cubic yards.
How much does a cubic yard of river rock weigh?
Usually around 1.25 to 1.45 tons, depending on stone size, fines and moisture.
How deep should river rock be for a walkway?
The table above shows 2 to 4 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 4x75?
300 square feet.
Related guides
- How Much Does a Ton of River Rock Cover?
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much River Rock for a 4x50 Walkway?
- How Much River Rock for a 4x60 Walkway?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.