How Much River Rock for a 5x30 Walkway?
How much river rock for a 5x30 walkway: at 3 inches deep you need about 1.39 cubic yards, which is roughly 1.9 tons at 1.35 tons per yard. The walkway covers 150 square feet, so every inch of depth adds about 0.46 yards.
Volume and tonnage calculator →The math for a 5x30 walkway
- Area: 5 × 30 = 150 sq ft.
- Depth in feet: 3 ÷ 12 = 0.250 ft.
- Cubic feet: 150 × 0.250 = 37.5 cu ft.
- Cubic yards: ÷ 27 = 1.39 yd³.
- Tons: × 1.35 = 1.9 tons.
The volume and tonnage calculator does this for any size.
River rock needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 2 in | 0.93 | 1.2 | 1.4 |
| 3 in | 1.39 | 1.9 | 2.1 |
| 4 in | 1.85 | 2.5 | 2.8 |
About river rock
River rock is smooth, water-worn stone sold in sizes from about 3/4 inch to several inches. Larger sizes cover fewer square feet per ton at the same depth because the voids between stones are bigger. Weight per yard is a planning number; the scale ticket at the yard is the real one.
Preparing the walkway
Dig the path a few inches below grade, compact the bottom, add fabric if needed and install edging on both sides so the material stays on the walk. This walkway sees foot traffic, so match the depth to that load rather than to the minimum.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 2.1 tons fits in a single typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the walkway as firm ground allows.
When to choose river rock
Good uses:
- Dry creek beds and drainage swales
- Decorative borders and planting beds
- Around downspouts to stop splash erosion
Less suited to:
- Walking surfaces
- Driveways
- Bases under slabs or pavers
Quick reference numbers
- Per inch over 100 sq ft: about 0.42 tons of river rock (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.2 tons.
- Another size for comparison: a 10x20 area at 4 inches takes about 3.3 tons.
- Weight used here: about 1.35 tons per cubic yard.
Common estimating mistakes
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
Questions people ask
How many tons of river rock for a 5x30 walkway?
About 1.9 tons at 3 inches deep, or 2.1 tons with 10 percent extra.
How many cubic yards is a 5x30 walkway at 3 inches?
About 1.39 cubic yards.
How much does a cubic yard of river rock weigh?
Usually around 1.25 to 1.45 tons, depending on stone size, fines and moisture.
How deep should river rock be for a walkway?
The table above shows 2 to 4 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 5x30?
150 square feet.
Related guides
- How Much Does a Ton of River Rock Cover?
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much River Rock for a 5x20 Walkway?
- How Much River Rock for a 5x25 Walkway?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.