How Much Sand for a 10x14 Patio?
How much sand for a 10x14 patio is a quick volume problem. 140 square feet at 3 inches comes to 1.30 cubic yards. Sand usually weighs about 1.3 to 1.5 dry tons per cubic yard, so plan on roughly 1.8 tons.
Volume and tonnage calculator →The math for a 10x14 patio
- Area: 10 × 14 = 140 sq ft.
- Depth in feet: 3 ÷ 12 = 0.250 ft.
- Cubic feet: 140 × 0.250 = 35.0 cu ft.
- Cubic yards: ÷ 27 = 1.30 yd³.
- Tons: × 1.35 = 1.8 tons.
The volume and tonnage calculator does this for any size.
Sand needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 1 in | 0.43 | 0.6 | 0.6 |
| 2 in | 0.86 | 1.2 | 1.3 |
| 3 in | 1.30 | 1.8 | 1.9 |
| 4 in | 1.73 | 2.3 | 2.6 |
About sand
Sand weight changes a lot with moisture. Damp sand can weigh noticeably more per yard than dry sand, so a ton of wet sand covers less area than the same ton dry. Ask your supplier for their own tons-per-yard figure, since stone source and moisture shift it.
Preparing the patio
Remove sod, level the area with a slight slope away from the house, and lay landscape fabric if weeds are a concern. Edging keeps loose material inside the patio footprint. This patio sees foot traffic and furniture, so match the depth to that load rather than to the minimum.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 1.9 tons fits in a single typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the patio as firm ground allows.
Good and poor uses for sand
Best suited to:
- Paver and flagstone bedding
- Leveling under above-ground pools (with the right product)
- Filling joints and backfilling pipe
Think twice for:
- Driveway bases, since sand shifts under load
- Steep areas exposed to runoff
- Thick layers under pavers, which settle unevenly
Quick reference numbers
- Per inch over 100 sq ft: about 0.42 tons of sand (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.2 tons.
- Another size for comparison: a 14x28 area at 2 inches takes about 3.3 tons.
- Weight used here: about 1.35 tons per cubic yard.
Common estimating mistakes
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
Questions people ask
How many tons of sand for a 10x14 patio?
About 1.8 tons at 3 inches deep, or 1.9 tons with 10 percent extra.
How many cubic yards is a 10x14 patio at 3 inches?
About 1.30 cubic yards.
How much does a cubic yard of sand weigh?
Usually around 1.3 to 1.5 dry tons, depending on stone size, fines and moisture.
How deep should sand be for a patio?
The table above shows 1 to 4 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 10x14?
140 square feet.
Related guides
- How Much Does a Ton of Sand Cover?
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much Sand for a 10x10 Patio?
- How Much Sand for a 10x12 Patio?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.