How Much Sand for a 6x60 Walkway?
A 6 by 60 foot walkway is 360 square feet. How much sand for a 6x60 walkway depends on depth: at 3 inches it is about 3.33 cubic yards or 4.5 tons. Suppliers usually sell by the ton, so the tonnage is the number to give them.
Volume and tonnage calculator →The math for a 6x60 walkway
- Area: 6 × 60 = 360 sq ft.
- Depth in feet: 3 ÷ 12 = 0.250 ft.
- Cubic feet: 360 × 0.250 = 90.0 cu ft.
- Cubic yards: ÷ 27 = 3.33 yd³.
- Tons: × 1.35 = 4.5 tons.
The volume and tonnage calculator does this for any size.
Sand needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 1 in | 1.11 | 1.5 | 1.7 |
| 2 in | 2.22 | 3.0 | 3.3 |
| 3 in | 3.33 | 4.5 | 5.0 |
| 4 in | 4.44 | 6.0 | 6.6 |
About sand
For paver bedding, concrete sand (coarse, washed) is the usual pick. Mason sand is finer and used in mortar and play areas. Weight per yard is a planning number; the scale ticket at the yard is the real one.
Preparing the walkway
Dig the path a few inches below grade, compact the bottom, add fabric if needed and install edging on both sides so the material stays on the walk. For foot traffic, the depths in the table above are a reasonable starting range.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 5.0 tons fits in a single typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the walkway as firm ground allows.
Where sand fits
Best suited to:
- Paver and flagstone bedding
- Leveling under above-ground pools (with the right product)
- Filling joints and backfilling pipe
Poor fit for:
- Driveway bases, since sand shifts under load
- Steep areas exposed to runoff
- Thick layers under pavers, which settle unevenly
Quick reference numbers
- Per inch over 100 sq ft: about 0.42 tons of sand (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.2 tons.
- Another size for comparison: a 20x25 area at 4 inches takes about 8.3 tons.
- Weight used here: about 1.35 tons per cubic yard.
Common estimating mistakes
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
Questions people ask
How many tons of sand for a 6x60 walkway?
About 4.5 tons at 3 inches deep, or 5.0 tons with 10 percent extra.
How many cubic yards is a 6x60 walkway at 3 inches?
About 3.33 cubic yards.
How much does a cubic yard of sand weigh?
Usually around 1.3 to 1.5 dry tons, depending on stone size, fines and moisture.
How deep should sand be for a walkway?
The table above shows 1 to 4 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 6x60?
360 square feet.
Related guides
- How Much Does a Ton of Sand Cover?
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much Sand for a 6x40 Walkway?
- How Much Sand for a 6x50 Walkway?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.