Jackhammer for Asphalt: Hammer Size, Bits and Safe Use
A jackhammer is the tool most people reach for when a section of asphalt has to come out: a sunken patch, a strip along a garage slab, a trench for a drain line, or a whole worn-out driveway. The catch is that asphalt doesn't break the way concrete does. The right hammer, and even more the right bit, makes the job go. Below: weight classes, bits, noise and vibration limits, and the tons you'll haul away.
Figuring what comes out? Open the asphalt tonnage calculator →Why asphalt needs a different approach than concrete
Concrete is brittle. A bull point drives a crack, and the slab breaks into chunks along it. Hot mix asphalt is aggregate held together by a flexible binder, so a narrow point tends to punch a hole and leaves the surrounding mat intact, especially once the pavement has warmed in the sun. That's why the bits sold for this job are wide and flat. Bosch's 5 in asphalt cutter, for example, is described by the maker as cutting "asphalt or hard ground" and listed as not for concrete. The wide edge slices the mat into strips you can pry up, rather than trying to shatter it.
On asphalt you are mostly cutting and peeling, not breaking, so a sharp, wide blade matters as much as hammer size.
Hammer weight classes compared
Rental yards and tool makers group these tools by weight class. The figures below are the published specs for real models, checked in November 2026. Vibration is the declared value for chiselling in concrete, so treat it as a comparison number.
| Class | Example model and published specs | Fits asphalt work like |
|---|---|---|
| 35–40 lb electric demolition hammer | Makita HM1307CB: 38.2 lb, 14 A, 34.9 J (25.7 ft-lb), 730–1,450 blows/min, 12 m/s² vibration, 101 dB(A), 1-1/8 in hex. Makita lists asphalt removal among its uses. | Squaring a patch, cutting out a strip along a slab or curb, thin residential pavement |
| 60–65 lb electric breaker | Bosch GSH 27 VC: 29.1 kg (about 64 lb), 2,000 W, 62 J, 920 blows/min, 9.7 m/s² (8.5 m/s² on some variants), 28 mm (1-1/8 in) hex | Full-depth driveway removal where a machine can't reach; thicker or older layered pavement |
| 70 lb electric breaker | Makita HM1812: 69.1 lb, 15 A, 72.8 J (53.9 ft-lb), 870 blows/min, 6.5 m/s², 106 dB(A), 1-1/8 in hex | Long days of breaking; heavy, layered or overlaid pavement on top of concrete |
| 90 lb class pneumatic paving breaker | Chicago Pneumatic CP 1290: 82 lb, 81 cfm of air at 90 psi, 3/4 in NPT inlet, 1-1/8 × 6 or 1-1/4 × 6 in hex shank | Contractor work with a tow-behind compressor already on site |
Two things jump out. First, the 70 lb electric hammer carries less than twice the weight of the 35 lb one but more than twice the impact energy. Second, the air breaker's 81 cfm demand is far beyond a garage compressor; it means a towable compressor, so for most homeowner jobs electric is the practical rental.
Electric or air?
For a homeowner or a small crew, an electric breaker is the simpler choice: no compressor, no hose, and it plugs into a standard outlet. The 70 lb Makita draws 15 amps, so give it a circuit that isn't feeding anything else and use the heavy cord the rental counter hands you rather than a thin household extension.
Air breakers make sense on contractor jobs where a towable compressor is already on site for other tools. If you're renting just to break up a driveway, the compressor rental and fuel add cost for no real gain.
Cold-weather tip from Bosch's manual for the GSH 27 VC: in low temperatures the hammer only reaches full impact power after it has run for a while, and you can shorten that warm-up by setting the bit on the ground and letting it strike once vertically. The same manual says to work with moderate pressure for the best vibration damping and to resharpen chisels before they go dull.
Bits that work in asphalt
- Asphalt cutter (wide flat blade). The workhorse. A 5 in blade such as the Bosch HS2167 5 in asphalt cutter with a 1-1/8 in hex shank (19 in overall) scores a line across the mat and slices it into slabs. Makita sells an equivalent 5 in cutter, the 751620-A.
- Clay spade. A broad, slightly dished blade for prying up cut slabs and digging into packed base or clay underneath. Makita's 751622-A clay spade, 5-1/2 × 20 in with a 1-1/8 in hex shank, is a common pick.
- Bull point. Usually included with the hammer (Makita ships a 20-1/2 in point with the HM1307CB). It's the right tool for concrete underneath an overlay, but in asphalt alone it tends to poke holes rather than break the mat.
Match the shank, not just the hex size. Most electric breakers in these classes take 1-1/8 in hex. Pneumatic breakers also specify a shank length; the CP 1290 comes in 1-1/8 × 6 in or 1-1/4 × 6 in, and bits are sold to fit each combination.
How to break up asphalt with a jackhammer
- Locate utilities first. If the work goes below the pavement, it's excavation. Michigan's Public Act 174, for example, requires a dig notice to MISS DIG 811 at least three business days (but no more than 14 calendar days) before you start, and Pennsylvania's PA One Call has the same three-business-day rule. Other states set their own notice period, but every state uses 811.
- Saw-cut the edges you're keeping. Where the old pavement meets a slab, a sidewalk, or asphalt that stays, cut a straight line first so the hammer doesn't tear the good side. Our saw-cut joint guide explains why a vertical face matters for the patch that goes back in.
- Start at an open edge. Work inward from a free edge or the saw cut, taking bites about a blade-width back from the edge so each strip has somewhere to go.
- Let the tool's weight do the work. Lean in only lightly.
- Pry and lift as you go. Switch to the clay spade or a pry bar to lift slabs, then stack the pieces so they're easy to load.
- Check what's underneath. If you hit concrete under an overlay, switch to the bull point.
For the bigger picture on whether to do it yourself or hire it out, see our guide to removing an old asphalt driveway, and for what contractors charge, our asphalt removal cost breakdown.
Noise and vibration: the real limit on how long you can run it
Jackhammers are loud. A CPWR hazard card for construction workers (published through the CDC) lists measured jackhammer noise at 102 to 111 dB, and OSHA's construction hearing toolbox talk uses about 110 dBA as the example. Makita's own spec sheets put the 35 lb hammer at 101 dB(A) and the 70 lb at 106 dB(A). NIOSH recommends double hearing protection, earplugs under earmuffs, for exposures of 100 dBA or more. A muff like the 3M PELTOR X5 earmuff (NRR 21 dB) over foam plugs is a sensible setup.
Vibration is the quieter hazard. The UK Health and Safety Executive sets a hand-arm vibration action value of 2.5 m/s² A(8) and a limit of 5.0 m/s². Its simple exposure-points table gives roughly 70 points an hour for a 6 m/s² tool, 200 for 10 m/s² and 300 for 12 m/s². The action value is 100 points a day and the limit is 400. Using the declared values above:
| Tool (declared vibration) | Approx. points per hour (HSE table) | Trigger time to action value | Trigger time to limit |
|---|---|---|---|
| Makita HM1307CB (12 m/s²) | ~300 | ~20 min | ~80 min |
| Bosch GSH 27 VC (9.7 m/s²) | ~200 | ~30 min | ~2 h |
| Makita HM1812 (6.5 m/s²) | ~70–100 | ~1–1.5 h | ~4–6 h |
"Trigger time" means time the hammer is actually running, not time on site. HSE also notes that people who regularly use hammer-action tools for more than about an hour a day are likely to be above the limit. That's a real argument for renting the bigger, vibration-damped hammer.
Dust matters too. OSHA's construction silica standard, Table 1, covers jackhammers and handheld chipping tools. Outdoors, it calls for either a continuous water spray at the point of impact or a commercial shroud with dust collection. Asphalt aggregate can contain silica, so keeping water on the point of impact, even from a helper with a garden hose, is a cheap habit worth keeping.
Worked example: how much asphalt are you going to haul?
Do this math before you book a dumpster or trailer. Michigan DOT's construction manual uses 110 lb per square yard for each inch of compacted hot mix. Breaking it up adds volume but not weight.
| Job | Area | Thickness | Math | Weight |
|---|---|---|---|---|
| Patch cut-out | 3 × 5 ft = 15 ft² (1.67 yd²) | 3 in | 1.67 × 3 × 110 | ~550 lb |
| Strip along a garage slab | 2 × 24 ft = 48 ft² (5.33 yd²) | 2 in | 5.33 × 2 × 110 | ~1,170 lb |
| Single-car driveway | 12 × 40 ft = 480 ft² (53.3 yd²) | 3 in | 53.3 × 3 × 110 | ~17,600 lb (8.8 tons) |
The driveway line is the eye-opener: nearly nine tons of asphalt, before any base gravel comes out. That's why our dumpster size for asphalt removal guide focuses on weight limits rather than cubic yards. Plug your own length, width and thickness into the asphalt calculator to get the tons, which is also the number you'll need when ordering new mix to replace it.
Rent, buy, or hire out?
- Rent for a one-time job. Ask for an asphalt cutter and clay spade with the hammer.
- Buy a 35–40 lb class hammer if you do recurring patch work. The Makita HM1307CB 35 lb demolition hammer takes standard 1-1/8 in hex bits and has variable speed for lighter cuts.
- Hire out anything over a few hundred square feet. A crew with a skid steer or mini-excavator lifts slabs far faster than hand work and handles the haul-off.
Jackhammer for asphalt FAQ
What size jackhammer do I need for asphalt?
For patches and edge strips, a 35 to 40 lb electric demolition hammer with a wide asphalt cutter bit is usually enough. For full-depth driveway removal, a 60 to 70 lb electric breaker hits about twice as hard; Makita rates its 70 lb HM1812 at 72.8 J versus 34.9 J for its 35 lb HM1307CB.
What is the best jackhammer bit for asphalt?
A wide flat asphalt cutter, typically 5 in across, slices the mat into strips. Bosch describes its HS2167 cutter as made for asphalt or hard ground and not for concrete. Use a clay spade to pry slabs up, and save the bull point for concrete underneath.
Can I use a jackhammer instead of a saw to cut a straight edge?
An asphalt cutter can score a rough line, but a saw cut gives the clean vertical face a new patch needs to bond against. Saw the edges you are keeping, then break out the rest with the hammer.
Do I need to call 811 before jackhammering a driveway?
If the work goes below the pavement, treat it as excavation. Michigan's Public Act 174 requires a dig notice to MISS DIG 811 at least three business days before you start, and Pennsylvania's PA One Call requires three business days too.
How loud is a jackhammer?
A CPWR hazard card lists jackhammers at 102 to 111 dB, and Makita lists 101 to 106 dB(A) for its electric hammers. NIOSH recommends earplugs plus earmuffs for exposures of 100 dBA or more.
The bottom line
For asphalt, the bit matters more than the hammer. A wide asphalt cutter turns even a 35 lb electric hammer into a useful tool for patches and edges, while full driveway removal goes faster and is easier on your hands with a vibration-damped 60–70 lb breaker. Saw-cut the edges you're keeping, call 811 before you go below the pavement, wear plugs and muffs, wet the dust, and keep track of trigger time.
Sources
- Makita HM1307CB 35 lb demolition hammer specifications and Makita HM1812 70 lb AVT breaker hammer specifications
- Bosch GSH 27 VC breaker technical data and GSH 27 VC operating manual
- Chicago Pneumatic CP 1290 pneumatic breaker specifications
- Bosch 1-1/8 in hex hammer steel catalog (HS2167 asphalt cutter, 5 in × 19 in)
- CPWR Hazard Alert: Construction Noise (CDC Stacks), OSHA Hearing Conservation in Construction toolbox talk and NIOSH: Provide Hearing Protection
- HSE: Control of Vibration at Work Regulations 2005 and HSE: Vibration risk assessment (exposure points table)
- OSHA 29 CFR 1926.1153, Respirable crystalline silica, Table 1
- MIOSHA Fact Sheet: MISS DIG 811, Public Act 174 and Pennsylvania PUC: PA One Call 811
- Michigan DOT Construction Manual, 501 Plant Produced Hot Mix Asphalt (110 lb/yd² per inch)
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.
