11 Cubic Yards of Gravel in Tons
11 cubic yards of gravel in tons works out to about 15.4 tons using a planning weight of 1.4 tons per yard. Real loads land between roughly 14.3 and 16.5 tons depending on stone size, fines and moisture. That is about 30,800 pounds.
Volume and tonnage calculator →The conversion
- Yards × tons per yard: 11 × 1.4 = 15.4 tons.
- Low end: 11 × 1.3 = 14.3 tons.
- High end: 11 × 1.5 = 16.5 tons.
Quarries can tell you the weight per yard for their own product; use it if you have it.
What 11 yards covers
| Depth | Square feet |
|---|---|
| 2 in | 1,782 |
| 3 in | 1,188 |
| 4 in | 891 |
| 6 in | 594 |
About gravel
Because ’gravel’ covers so many products, the weight per yard moves with stone size and how much fine material is in the pile. Rounded stone with no fines rolls under tires; crushed stone with fines locks together.
Hauling 11 yards
Plan the delivery around 15.4 tons: one tandem in most areas. A pickup is a poor fit for anything past a fraction of a yard; see how much gravel a half-ton pickup can carry.
Before you order
- Confirm whether the yard prices gravel by the ton or by the yard.
- Add about 10 percent for compaction and uneven ground.
- Clear a firm spot for the truck to dump.
The volume and tonnage calculator converts any area and depth into yards and tons.
Good and poor uses for gravel
Good uses:
- Rural driveways and lanes where low upfront cost matters
- Drainage areas and around downspouts
- Temporary access while a site is under construction
Less suited to:
- Steep slopes, where loose stone washes downhill
- Spots plowed often, since plows push gravel into the lawn
- Areas next to doors, because stone tracks inside
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of gravel (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 20x25 area at 2 inches takes about 4.3 tons.
- Weight used here: about 1.4 tons per cubic yard.
Mistakes that throw off the order
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
Questions people ask
How many tons is 11 yards of gravel?
About 15.4 tons, with a typical range of 14.3 to 16.5.
How many pounds is 11 cubic yards of gravel?
About 30,800 pounds.
How much area does 11 yards of gravel cover at 4 inches?
About 891 square feet.
Why does gravel weight vary?
Stone size, the share of fines and moisture all change how much a yard weighs.
Is it better to buy by the ton or the yard?
Either works; just convert with the supplier’s own weight per yard so the two quotes compare fairly.
Related guides
- How Much Does a Ton of Gravel Cover? Depth Chart
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Much Does a Yard of Crushed Stone Weigh?
- 9 Cubic Yards of Gravel in Tons
- 10 Cubic Yards of Gravel in Tons
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.