13 Cubic Yards of Gravel in Tons
13 cubic yards of gravel in tons works out to about 18.2 tons using a planning weight of 1.4 tons per yard. Real loads land between roughly 16.9 and 19.5 tons depending on stone size, fines and moisture. That is about 36,400 pounds.
Volume and tonnage calculator →The conversion
- Yards × tons per yard: 13 × 1.4 = 18.2 tons.
- Low end: 13 × 1.3 = 16.9 tons.
- High end: 13 × 1.5 = 19.5 tons.
If your supplier quotes a different weight per yard, multiply by theirs.
What 13 yards covers
| Depth | Square feet |
|---|---|
| 2 in | 2,106 |
| 3 in | 1,404 |
| 4 in | 1,053 |
| 6 in | 702 |
About gravel
Plain gravel is a loose term. Yards use it for rounded bank or river stone as well as for crushed rock, so ask whether the load is washed, crushed or a mix before you lock in a tonnage.
Hauling 13 yards
Plan the delivery around 18.2 tons: two or more trucks in most areas. A pickup is a poor fit for anything past a fraction of a yard; see how much gravel a half-ton pickup can carry.
Before you order
- Confirm whether the yard prices gravel by the ton or by the yard.
- Add about 10 percent for compaction and uneven ground.
- Clear a firm spot for the truck to dump.
The volume and tonnage calculator converts any area and depth into yards and tons.
Where gravel fits
Good uses:
- Rural driveways and lanes where low upfront cost matters
- Drainage areas and around downspouts
- Temporary access while a site is under construction
Poor fit for:
- Steep slopes, where loose stone washes downhill
- Spots plowed often, since plows push gravel into the lawn
- Areas next to doors, because stone tracks inside
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of gravel (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 10x20 area at 3 inches takes about 2.6 tons.
- Weight used here: about 1.4 tons per cubic yard.
Common estimating mistakes
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
Questions people ask
How many tons is 13 yards of gravel?
About 18.2 tons, with a typical range of 16.9 to 19.5.
How many pounds is 13 cubic yards of gravel?
About 36,400 pounds.
How much area does 13 yards of gravel cover at 4 inches?
About 1,053 square feet.
Why does gravel weight vary?
Stone size, the share of fines and moisture all change how much a yard weighs.
Is it better to buy by the ton or the yard?
Either works; just convert with the supplier’s own weight per yard so the two quotes compare fairly.
Related guides
- How Much Does a Ton of Gravel Cover? Depth Chart
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Much Does a Yard of Crushed Stone Weigh?
- 11 Cubic Yards of Gravel in Tons
- 12 Cubic Yards of Gravel in Tons
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.