30 Cubic Yards of Recycled Concrete Aggregate in Tons
30 cubic yards of recycled concrete aggregate in tons works out to about 39.0 tons using a planning weight of 1.3 tons per yard. Real loads land between roughly 36.0 and 42.0 tons depending on stone size, fines and moisture. That is about 78,000 pounds.
Volume and tonnage calculator →The conversion
- Yards × tons per yard: 30 × 1.3 = 39.0 tons.
- Low end: 30 × 1.2 = 36.0 tons.
- High end: 30 × 1.4 = 42.0 tons.
Quarries can tell you the weight per yard for their own product; use it if you have it.
What 30 yards covers
| Depth | Square feet |
|---|---|
| 3 in | 3,240 |
| 4 in | 2,430 |
| 6 in | 1,620 |
About recycled concrete aggregate
Recycled concrete aggregate is crushed old concrete. It compacts well and often costs less than virgin stone, which makes it a common driveway and pad base.
Hauling 30 yards
Plan the delivery around 39.0 tons: two or more trucks in most areas. A pickup is a poor fit for anything past a fraction of a yard; see how much gravel a half-ton pickup can carry.
Before you order
- Confirm whether the yard prices recycled concrete aggregate by the ton or by the yard.
- Add about 10 percent for compaction and uneven ground.
- Clear a firm spot for the truck to dump.
The volume and tonnage calculator converts any area and depth into yards and tons.
Good and poor uses for recycled concrete aggregate
Good uses:
- Driveway and pad bases
- Temporary construction entrances
- Fill under slabs when compacted in lifts
Poor fit for:
- Near ponds, streams or sensitive plants, since fresh crush can raise pH
- Decorative top layers
- Drainage layers, unless the product is clean and screened
Quick reference numbers
- Per inch over 100 sq ft: about 0.40 tons of recycled concrete aggregate (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.0 tons.
- Another size for comparison: a 15x30 area at 4 inches takes about 7.2 tons.
- Weight used here: about 1.3 tons per cubic yard.
Where estimates go wrong
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
Questions people ask
How many tons is 30 yards of recycled concrete aggregate?
About 39.0 tons, with a typical range of 36.0 to 42.0.
How many pounds is 30 cubic yards of recycled concrete aggregate?
About 78,000 pounds.
How much area does 30 yards of recycled concrete aggregate cover at 4 inches?
About 2,430 square feet.
Why does recycled concrete aggregate weight vary?
Stone size, the share of fines and moisture all change how much a yard weighs.
Is it better to buy by the ton or the yard?
Either works; just convert with the supplier’s own weight per yard so the two quotes compare fairly.
Related guides
- Crushed Stone vs Gravel: Differences and Best Uses
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Much Does a Yard of Crushed Stone Weigh?
- 20 Cubic Yards of Recycled Concrete Aggregate in Tons
- 25 Cubic Yards of Recycled Concrete Aggregate in Tons
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.