40 Cubic Yards of Crusher Run in Tons
40 cubic yards of crusher run in tons works out to about 62.0 tons using a planning weight of 1.55 tons per yard. Real loads land between roughly 60.0 and 68.0 tons depending on stone size, fines and moisture. That is about 124,000 pounds.
Volume and tonnage calculator →The conversion
- Yards × tons per yard: 40 × 1.55 = 62.0 tons.
- Low end: 40 × 1.5 = 60.0 tons.
- High end: 40 × 1.7 = 68.0 tons.
The scale ticket on delivery day is the final word on weight.
What 40 yards covers
| Depth | Square feet |
|---|---|
| 3 in | 4,320 |
| 4 in | 3,240 |
| 6 in | 2,160 |
| 8 in | 1,620 |
About crusher run
Crusher run (also sold as crush and run, dense-grade aggregate or QP in some regions) mixes stone with stone dust. It compacts into a firm, nearly solid layer, which makes it the usual base under pavers, asphalt and gravel drives.
Hauling 40 yards
At about 62.0 tons, this is more than one typical truckload. A pickup is a poor fit for anything past a fraction of a yard; see how much gravel a half-ton pickup can carry.
Before you order
- Confirm whether the yard prices crusher run by the ton or by the yard.
- Add about 10 percent for compaction and uneven ground.
- Clear a firm spot for the truck to dump.
The volume and tonnage calculator converts any area and depth into yards and tons.
Where crusher run fits
Best suited to:
- Base under asphalt, pavers or concrete
- Gravel drives that need a firm, packed surface
- Shed pads and equipment pads
Less suited to:
- Drainage layers, since the fines slow water
- Decorative beds
- Spots where you want water to soak straight through
Quick reference numbers
- Per inch over 100 sq ft: about 0.48 tons of crusher run (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.8 tons.
- Another size for comparison: a 15x30 area at 4 inches takes about 8.6 tons.
- Weight used here: about 1.55 tons per cubic yard.
Where estimates go wrong
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
Questions people ask
How many tons is 40 yards of crusher run?
About 62.0 tons, with a typical range of 60.0 to 68.0.
How many pounds is 40 cubic yards of crusher run?
About 124,000 pounds.
How much area does 40 yards of crusher run cover at 6 inches?
About 2,160 square feet.
Why does crusher run weight vary?
Stone size, the share of fines and moisture all change how much a yard weighs.
Is it better to buy by the ton or the yard?
Either works; just convert with the supplier’s own weight per yard so the two quotes compare fairly.
Related guides
- Crushed Stone vs Gravel: Differences and Best Uses
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Much Does a Yard of Crushed Stone Weigh?
- 25 Cubic Yards of Crusher Run in Tons
- 30 Cubic Yards of Crusher Run in Tons
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.