7 Cubic Yards of Crusher Run in Tons
7 cubic yards of crusher run in tons works out to about 10.8 tons using a planning weight of 1.55 tons per yard. Real loads land between roughly 10.5 and 11.9 tons depending on stone size, fines and moisture. That is about 21,700 pounds.
Volume and tonnage calculator →The conversion
- Yards × tons per yard: 7 × 1.55 = 10.8 tons.
- Low end: 7 × 1.5 = 10.5 tons.
- High end: 7 × 1.7 = 11.9 tons.
If your supplier quotes a different weight per yard, multiply by theirs.
What 7 yards covers
| Depth | Square feet |
|---|---|
| 3 in | 756 |
| 4 in | 567 |
| 6 in | 378 |
| 8 in | 284 |
About crusher run
Crusher run (also sold as crush and run, dense-grade aggregate or QP in some regions) mixes stone with stone dust. It compacts into a firm, nearly solid layer, which makes it the usual base under pavers, asphalt and gravel drives.
Hauling 7 yards
At about 10.8 tons, this is roughly a tandem-axle truckload. A pickup is a poor fit for anything past a fraction of a yard; see how much gravel a half-ton pickup can carry.
Before you order
- Confirm whether the yard prices crusher run by the ton or by the yard.
- Add about 10 percent for compaction and uneven ground.
- Clear a firm spot for the truck to dump.
The volume and tonnage calculator converts any area and depth into yards and tons.
Good and poor uses for crusher run
Best suited to:
- Base under asphalt, pavers or concrete
- Gravel drives that need a firm, packed surface
- Shed pads and equipment pads
Think twice for:
- Drainage layers, since the fines slow water
- Decorative beds
- Spots where you want water to soak straight through
Quick reference numbers
- Per inch over 100 sq ft: about 0.48 tons of crusher run (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.8 tons.
- Another size for comparison: a 12x24 area at 3 inches takes about 4.1 tons.
- Weight used here: about 1.55 tons per cubic yard.
Mistakes that throw off the order
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
Questions people ask
How many tons is 7 yards of crusher run?
About 10.8 tons, with a typical range of 10.5 to 11.9.
How many pounds is 7 cubic yards of crusher run?
About 21,700 pounds.
How much area does 7 yards of crusher run cover at 6 inches?
About 378 square feet.
Why does crusher run weight vary?
Stone size, the share of fines and moisture all change how much a yard weighs.
Is it better to buy by the ton or the yard?
Either works; just convert with the supplier’s own weight per yard so the two quotes compare fairly.
Related guides
- Crushed Stone vs Gravel: Differences and Best Uses
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Much Does a Yard of Crushed Stone Weigh?
- 5 Cubic Yards of Crusher Run in Tons
- 6 Cubic Yards of Crusher Run in Tons
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.