How Much #57 Stone for a 10x45 Driveway?
A 10 by 45 foot driveway is 450 square feet. How much #57 stone for a 10x45 driveway depends on depth: at 4 inches it is about 5.56 cubic yards or 7.5 tons. Suppliers usually sell by the ton, so the tonnage is the number to give them.
Volume and tonnage calculator →The math for a 10x45 driveway
- Area: 10 × 45 = 450 sq ft.
- Depth in feet: 4 ÷ 12 = 0.333 ft.
- Cubic feet: 450 × 0.333 = 150.0 cu ft.
- Cubic yards: ÷ 27 = 5.56 yd³.
- Tons: × 1.35 = 7.5 tons.
The volume and tonnage calculator does this for any size.
#57 stone needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 2 in | 2.78 | 3.8 | 4.1 |
| 3 in | 4.17 | 5.6 | 6.2 |
| 4 in | 5.56 | 7.5 | 8.2 |
| 6 in | 8.33 | 11.3 | 12.4 |
About #57 stone
#57 stone is a clean crushed stone in roughly the 1/2 to 1 inch range with very few fines. It drains fast, which suits drainage layers and the top of a gravel drive, but it does not pack into a hard crust by itself. If the yard sells by the cubic yard instead of the ton, use the cubic-yard column directly.
Preparing the driveway
Strip sod and soft topsoil, grade for drainage and compact the subgrade before any stone goes down. Gravel drives last longer with a compacted base layer under the top stone and a slight crown so water runs off. This driveway sees car and truck traffic, so match the depth to that load rather than to the minimum.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 8.2 tons fits in a single typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the driveway as firm ground allows.
Where #57 stone fits
Works well for:
- French drains and drainage layers
- The top course of a gravel driveway
- Under sheds where water needs to drain away
Poor fit for:
- A standalone base, since it does not pack hard without fines
- Paver setting beds
- Walk paths meant for strollers or wheelchairs
Quick reference numbers
- Per inch over 100 sq ft: about 0.42 tons of #57 stone (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.2 tons.
- Another size for comparison: a 8x16 area at 4 inches takes about 2.1 tons.
- Weight used here: about 1.35 tons per cubic yard.
Common estimating mistakes
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
Questions people ask
How many tons of #57 stone for a 10x45 driveway?
About 7.5 tons at 4 inches deep, or 8.2 tons with 10 percent extra.
How many cubic yards is a 10x45 driveway at 4 inches?
About 5.56 cubic yards.
How much does a cubic yard of #57 stone weigh?
Usually around 1.3 to 1.45 tons, depending on stone size, fines and moisture.
How deep should #57 stone be for a driveway?
The table above shows 2 to 6 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 10x45?
450 square feet.
Related guides
- Number 57 Stone: Size, Weight, Uses, and Coverage
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much #57 Stone for a 10x35 Driveway?
- How Much #57 Stone for a 10x40 Driveway?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.