How Much Asphalt Millings for a 18x30 Parking Pad?

How much asphalt millings for a 18x30 parking pad is a quick volume problem. 540 square feet at 4 inches comes to 6.67 cubic yards. Asphalt millings usually weighs about 1.2 to 1.4 loose tons per cubic yard, so plan on roughly 8.7 tons.

Volume and tonnage calculator →

The math for a 18x30 parking pad

Area: 18 × 30 = 540 sq ft.
Depth in feet: 4 ÷ 12 = 0.333 ft.
Cubic feet: 540 × 0.333 = 180.0 cu ft.
Cubic yards: ÷ 27 = 6.67 yd³.
Tons: × 1.3 = 8.7 tons.

The volume and tonnage calculator does this for any size.

Asphalt millings needed by depth

Depth	Cubic yards	Tons (approx.)	Tons +10%
3 in	5.00	6.5	7.2
4 in	6.67	8.7	9.5
6 in	10.00	13.0	14.3

About asphalt millings

Millings vary by source: some loads are fine and uniform, others carry chunks. Ask the supplier for a screened product if you want a smoother finish, and check local rules, since some areas restrict their use near water. Weight per yard is a planning number; the scale ticket at the yard is the real one.

Preparing the parking pad

Dig out organic soil, compact the subgrade and set an edge so the stone does not migrate onto the lawn. A pad that holds parked weight for long periods benefits from a dense base under the surface stone. Since the parking pad carries parked vehicles, a little extra depth is cheap insurance.

Ordering tips

Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
Delivery size. 9.5 tons fits in a single typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
Bulk vs bags. At this size bulk delivery is usually the practical choice.
Where it drops. Have the truck dump as close to the parking pad as firm ground allows.

Good and poor uses for asphalt millings

Best suited to:

Rural driveways and farm lanes
Parking areas where a dust-free surface is wanted
Low-cost base under a future paved surface

Think twice for:

Areas near wells or streams where local rules limit them
Decorative or barefoot areas
Jobs needing a uniform, clean look

Quick reference numbers

Per inch over 100 sq ft: about 0.40 tons of asphalt millings (0.31 cubic yards).
Per inch over 1,000 sq ft: about 4.0 tons.
Another size for comparison: a 8x16 area at 3 inches takes about 1.5 tons.
Weight used here: about 1.3 tons per cubic yard.

Common estimating mistakes

Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.

Questions people ask

How many tons of asphalt millings for a 18x30 parking pad?

About 8.7 tons at 4 inches deep, or 9.5 tons with 10 percent extra.

How many cubic yards is a 18x30 parking pad at 4 inches?

About 6.67 cubic yards.

How much does a cubic yard of asphalt millings weigh?

Usually around 1.2 to 1.4 loose tons, depending on stone size, fines and moisture.

How deep should asphalt millings be for a parking pad?

The table above shows 3 to 6 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.

How many square feet is 18x30?

540 square feet.

As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.