How Much Asphalt Millings for a 24x50 Parking Pad?

How much asphalt millings for a 24x50 parking pad: at 4 inches deep you need about 14.81 cubic yards, which is roughly 19.3 tons at 1.3 tons per yard. The parking pad covers 1,200 square feet, so every inch of depth adds about 3.70 yards.

Volume and tonnage calculator →

The math for a 24x50 parking pad

Area: 24 × 50 = 1,200 sq ft.
Depth in feet: 4 ÷ 12 = 0.333 ft.
Cubic feet: 1,200 × 0.333 = 400.0 cu ft.
Cubic yards: ÷ 27 = 14.81 yd³.
Tons: × 1.3 = 19.3 tons.

The volume and tonnage calculator does this for any size.

Asphalt millings needed by depth

Depth	Cubic yards	Tons (approx.)	Tons +10%
3 in	11.11	14.4	15.9
4 in	14.81	19.3	21.2
6 in	22.22	28.9	31.8

About asphalt millings

Millings vary by source: some loads are fine and uniform, others carry chunks. Ask the supplier for a screened product if you want a smoother finish, and check local rules, since some areas restrict their use near water. If the yard sells by the cubic yard instead of the ton, use the cubic-yard column directly.

Preparing the parking pad

Dig out organic soil, compact the subgrade and set an edge so the stone does not migrate onto the lawn. A pad that holds parked weight for long periods benefits from a dense base under the surface stone. For parked vehicles, the depths in the table above are a reasonable starting range.

Ordering tips

Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
Delivery size. 21.2 tons may take more than one typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
Bulk vs bags. At this size bulk delivery is usually the practical choice.
Where it drops. Have the truck dump as close to the parking pad as firm ground allows.

When to choose asphalt millings

Works well for:

Rural driveways and farm lanes
Parking areas where a dust-free surface is wanted
Low-cost base under a future paved surface

Less suited to:

Areas near wells or streams where local rules limit them
Decorative or barefoot areas
Jobs needing a uniform, clean look

Quick reference numbers

Per inch over 100 sq ft: about 0.40 tons of asphalt millings (0.31 cubic yards).
Per inch over 1,000 sq ft: about 4.0 tons.
Another size for comparison: a 14x28 area at 3 inches takes about 4.7 tons.
Weight used here: about 1.3 tons per cubic yard.

Common estimating mistakes

Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.

Questions people ask

How many tons of asphalt millings for a 24x50 parking pad?

About 19.3 tons at 4 inches deep, or 21.2 tons with 10 percent extra.

How many cubic yards is a 24x50 parking pad at 4 inches?

About 14.81 cubic yards.

How much does a cubic yard of asphalt millings weigh?

Usually around 1.2 to 1.4 loose tons, depending on stone size, fines and moisture.

How deep should asphalt millings be for a parking pad?

The table above shows 3 to 6 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.

How many square feet is 24x50?

1,200 square feet.

As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.