How Much Road Base for a 24x50 Parking Pad?
How much road base for a 24x50 parking pad: at 4 inches deep you need about 14.81 cubic yards, which is roughly 22.2 tons at 1.5 tons per yard. The parking pad covers 1,200 square feet, so every inch of depth adds about 3.70 yards.
Volume and tonnage calculator →The math for a 24x50 parking pad
- Area: 24 × 50 = 1,200 sq ft.
- Depth in feet: 4 ÷ 12 = 0.333 ft.
- Cubic feet: 1,200 × 0.333 = 400.0 cu ft.
- Cubic yards: ÷ 27 = 14.81 yd³.
- Tons: × 1.5 = 22.2 tons.
The volume and tonnage calculator does this for any size.
Road base needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 4 in | 14.81 | 22.2 | 24.4 |
| 6 in | 22.22 | 33.3 | 36.7 |
| 8 in | 29.63 | 44.4 | 48.9 |
About road base
Road base is meant to be compacted at close to the right moisture. Dry base rock does not lock up well; a light spray of water before rolling helps. Ask your supplier for their own tons-per-yard figure, since stone source and moisture shift it.
Preparing the parking pad
Dig out organic soil, compact the subgrade and set an edge so the stone does not migrate onto the lawn. A pad that holds parked weight for long periods benefits from a dense base under the surface stone. For parked vehicles, the depths in the table above are a reasonable starting range.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 24.4 tons may take more than one typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the parking pad as firm ground allows.
Where road base fits
Works well for:
- Base under asphalt and concrete
- Gravel roads and drives
- Equipment and shed pads
Less suited to:
- Drainage layers
- Decorative surfaces
- Surfaces that will stay uncompacted
Quick reference numbers
- Per inch over 100 sq ft: about 0.46 tons of road base (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.6 tons.
- Another size for comparison: a 14x28 area at 4 inches takes about 7.3 tons.
- Weight used here: about 1.5 tons per cubic yard.
Where estimates go wrong
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
Questions people ask
How many tons of road base for a 24x50 parking pad?
About 22.2 tons at 4 inches deep, or 24.4 tons with 10 percent extra.
How many cubic yards is a 24x50 parking pad at 4 inches?
About 14.81 cubic yards.
How much does a cubic yard of road base weigh?
Usually around 1.4 to 1.65 compacted tons, depending on stone size, fines and moisture.
How deep should road base be for a parking pad?
The table above shows 4 to 8 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 24x50?
1,200 square feet.
Related guides
- Crushed Stone vs Gravel: Differences and Best Uses
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much Road Base for a 24x36 Parking Pad?
- How Much Road Base for a 24x40 Parking Pad?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.