How Much Road Base for a 24x50 Driveway?
How much road base for a 24x50 driveway is a quick volume problem. 1,200 square feet at 4 inches comes to 14.81 cubic yards. Road base usually weighs about 1.4 to 1.65 compacted tons per cubic yard, so plan on roughly 22.2 tons.
Volume and tonnage calculator →The math for a 24x50 driveway
- Area: 24 × 50 = 1,200 sq ft.
- Depth in feet: 4 ÷ 12 = 0.333 ft.
- Cubic feet: 1,200 × 0.333 = 400.0 cu ft.
- Cubic yards: ÷ 27 = 14.81 yd³.
- Tons: × 1.5 = 22.2 tons.
The volume and tonnage calculator does this for any size.
Road base needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 4 in | 14.81 | 22.2 | 24.4 |
| 6 in | 22.22 | 33.3 | 36.7 |
| 8 in | 29.63 | 44.4 | 48.9 |
About road base
Road base is meant to be compacted at close to the right moisture. Dry base rock does not lock up well; a light spray of water before rolling helps. Weight per yard is a planning number; the scale ticket at the yard is the real one.
Preparing the driveway
Strip sod and soft topsoil, grade for drainage and compact the subgrade before any stone goes down. Gravel drives last longer with a compacted base layer under the top stone and a slight crown so water runs off. For car and truck traffic, the depths in the table above are a reasonable starting range.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 24.4 tons may take more than one typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the driveway as firm ground allows.
When to choose road base
Works well for:
- Base under asphalt and concrete
- Gravel roads and drives
- Equipment and shed pads
Think twice for:
- Drainage layers
- Decorative surfaces
- Surfaces that will stay uncompacted
Quick reference numbers
- Per inch over 100 sq ft: about 0.46 tons of road base (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.6 tons.
- Another size for comparison: a 15x30 area at 4 inches takes about 8.3 tons.
- Weight used here: about 1.5 tons per cubic yard.
Common estimating mistakes
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
Questions people ask
How many tons of road base for a 24x50 driveway?
About 22.2 tons at 4 inches deep, or 24.4 tons with 10 percent extra.
How many cubic yards is a 24x50 driveway at 4 inches?
About 14.81 cubic yards.
How much does a cubic yard of road base weigh?
Usually around 1.4 to 1.65 compacted tons, depending on stone size, fines and moisture.
How deep should road base be for a driveway?
The table above shows 4 to 8 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 24x50?
1,200 square feet.
Related guides
- Crushed Stone vs Gravel: Differences and Best Uses
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much Road Base for a 24x40 Driveway?
- How Much Road Base for a 24x45 Driveway?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.