How Much Asphalt Millings for a 30x20 Parking Pad?

How much asphalt millings for a 30x20 parking pad: at 4 inches deep you need about 7.41 cubic yards, which is roughly 9.6 tons at 1.3 tons per yard. The parking pad covers 600 square feet, so every inch of depth adds about 1.85 yards.

Volume and tonnage calculator →

The math for a 30x20 parking pad

Area: 30 × 20 = 600 sq ft.
Depth in feet: 4 ÷ 12 = 0.333 ft.
Cubic feet: 600 × 0.333 = 200.0 cu ft.
Cubic yards: ÷ 27 = 7.41 yd³.
Tons: × 1.3 = 9.6 tons.

The volume and tonnage calculator does this for any size.

Asphalt millings needed by depth

Depth	Cubic yards	Tons (approx.)	Tons +10%
3 in	5.56	7.2	7.9
4 in	7.41	9.6	10.6
6 in	11.11	14.4	15.9

About asphalt millings

Millings vary by source: some loads are fine and uniform, others carry chunks. Ask the supplier for a screened product if you want a smoother finish, and check local rules, since some areas restrict their use near water. Weight per yard is a planning number; the scale ticket at the yard is the real one.

Preparing the parking pad

Dig out organic soil, compact the subgrade and set an edge so the stone does not migrate onto the lawn. A pad that holds parked weight for long periods benefits from a dense base under the surface stone. This parking pad sees parked vehicles, so match the depth to that load rather than to the minimum.

Ordering tips

Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
Delivery size. 10.6 tons fits in a single typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
Bulk vs bags. At this size bulk delivery is usually the practical choice.
Where it drops. Have the truck dump as close to the parking pad as firm ground allows.

Where asphalt millings fits

Good uses:

Rural driveways and farm lanes
Parking areas where a dust-free surface is wanted
Low-cost base under a future paved surface

Less suited to:

Areas near wells or streams where local rules limit them
Decorative or barefoot areas
Jobs needing a uniform, clean look

Quick reference numbers

Per inch over 100 sq ft: about 0.40 tons of asphalt millings (0.31 cubic yards).
Per inch over 1,000 sq ft: about 4.0 tons.
Another size for comparison: a 20x25 area at 3 inches takes about 6.0 tons.
Weight used here: about 1.3 tons per cubic yard.

Common estimating mistakes

Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.

Questions people ask

How many tons of asphalt millings for a 30x20 parking pad?

About 9.6 tons at 4 inches deep, or 10.6 tons with 10 percent extra.

How many cubic yards is a 30x20 parking pad at 4 inches?

About 7.41 cubic yards.

How much does a cubic yard of asphalt millings weigh?

Usually around 1.2 to 1.4 loose tons, depending on stone size, fines and moisture.

How deep should asphalt millings be for a parking pad?

The table above shows 3 to 6 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.

How many square feet is 30x20?

600 square feet.

As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.