How Much Crushed Stone for a 10x200 Driveway?
A 10 by 200 foot driveway is 2,000 square feet. How much crushed stone for a 10x200 driveway depends on depth: at 4 inches it is about 24.69 cubic yards or 34.6 tons. Suppliers usually sell by the ton, so the tonnage is the number to give them.
Volume and tonnage calculator →The math for a 10x200 driveway
- Area: 10 × 200 = 2,000 sq ft.
- Depth in feet: 4 ÷ 12 = 0.333 ft.
- Cubic feet: 2,000 × 0.333 = 666.7 cu ft.
- Cubic yards: ÷ 27 = 24.69 yd³.
- Tons: × 1.4 = 34.6 tons.
The volume and tonnage calculator does this for any size.
Crushed stone needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 2 in | 12.35 | 17.3 | 19.0 |
| 3 in | 18.52 | 25.9 | 28.5 |
| 4 in | 24.69 | 34.6 | 38.0 |
| 6 in | 37.04 | 51.9 | 57.0 |
About crushed stone
Most quarries sell crushed stone by a size number or a screen size. Clean crushed stone drains well; stone with fines packs harder but sheds water more slowly. If the yard sells by the cubic yard instead of the ton, use the cubic-yard column directly.
Preparing the driveway
Strip sod and soft topsoil, grade for drainage and compact the subgrade before any stone goes down. Gravel drives last longer with a compacted base layer under the top stone and a slight crown so water runs off. Since the driveway carries car and truck traffic, a little extra depth is cheap insurance.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 38.0 tons may take more than one typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the driveway as firm ground allows.
Good and poor uses for crushed stone
Works well for:
- Driveway top courses and parking pads
- Shed and hot tub bases
- Backfill behind walls when a clean size is used
Less suited to:
- Barefoot areas, since angular stone is rough
- Play areas
- Places that need a smooth rolling surface for wheels
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of crushed stone (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 20x25 area at 4 inches takes about 8.6 tons.
- Weight used here: about 1.4 tons per cubic yard.
Common estimating mistakes
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
Questions people ask
How many tons of crushed stone for a 10x200 driveway?
About 34.6 tons at 4 inches deep, or 38.0 tons with 10 percent extra.
How many cubic yards is a 10x200 driveway at 4 inches?
About 24.69 cubic yards.
How much does a cubic yard of crushed stone weigh?
Usually around 1.35 to 1.5 tons, depending on stone size, fines and moisture.
How deep should crushed stone be for a driveway?
The table above shows 2 to 6 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 10x200?
2,000 square feet.
Related guides
- How Much Does a Ton of Crushed Stone Cover?
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much Crushed Stone for a 10x120 Driveway?
- How Much Crushed Stone for a 10x150 Driveway?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.