How Much Crusher Run for 250 Square Feet?
How much crusher run for 250 square feet depends on depth. At 6 inches you need about 4.63 cubic yards, roughly 7.2 tons at 1.55 tons per yard. Going to 8 inches raises it to 9.6 tons.
Volume and tonnage calculator →Crusher run for 250 sq ft by depth
| Depth | Cubic yards | Tons | Tons +10% |
|---|---|---|---|
| 3 in | 2.31 | 3.6 | 3.9 |
| 4 in | 3.09 | 4.8 | 5.3 |
| 6 in | 4.63 | 7.2 | 7.9 |
| 8 in | 6.17 | 9.6 | 10.5 |
Working it out
- 250 sq ft × (6 ÷ 12) ft = 125.0 cubic feet.
- ÷ 27 = 4.63 cubic yards.
- × 1.55 tons per yard = 7.2 tons.
About crusher run
The fines in crusher run fill the gaps between stones, so it weighs more per yard than clean stone once compacted. Plan on rolling or plate-compacting it in lifts. Most suppliers will quote 1.5 to 1.7 compacted tons per yard for this material.
Ordering checklist
- Measure odd shapes in pieces. Split curves and L-shapes into rectangles and add them.
- Add a margin. About 10 percent covers compaction and low spots.
- Bulk or bags. Bulk delivery is the practical choice here.
- Prep first. Remove sod, compact the subgrade and set edging before the stone arrives.
Use the volume and tonnage calculator for any other size.
Where crusher run fits
Best suited to:
- Base under asphalt, pavers or concrete
- Gravel drives that need a firm, packed surface
- Shed pads and equipment pads
Poor fit for:
- Drainage layers, since the fines slow water
- Decorative beds
- Spots where you want water to soak straight through
Quick reference numbers
- Per inch over 100 sq ft: about 0.48 tons of crusher run (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.8 tons.
- Another size for comparison: a 8x16 area at 2 inches takes about 1.2 tons.
- Weight used here: about 1.55 tons per cubic yard.
Common estimating mistakes
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
Questions people ask
How many tons of crusher run for 250 square feet?
About 7.2 tons at 6 inches deep.
How many cubic yards of crusher run for 250 square feet?
About 4.63 yards at 6 inches.
How much crusher run for 250 square feet at 3 inches?
About 3.6 tons, or 2.31 cubic yards.
How much does a yard of crusher run weigh?
About 1.5 to 1.7 compacted tons.
Should I add extra?
Yes, about 10 percent is a common allowance.
Related guides
- Crushed Stone vs Gravel: Differences and Best Uses
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much Crusher Run for 150 Square Feet?
- How Much Crusher Run for 200 Square Feet?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.