How Much Does 11 Tons of Road Base Cover?
How much does 11 tons of road base cover depends on how deep you spread it. At about 1.5 tons per cubic yard, 11 tons is roughly 7.3 cubic yards. Spread 6 inches deep, that covers about 396 square feet. Halve the depth and you roughly double the area.
Volume and tonnage calculator →How the coverage is figured
- Tons to cubic yards: 11 ÷ 1.5 = 7.3 yd³.
- Cubic yards to cubic feet: × 27 = 198 cu ft.
- Divide by depth in feet: at 6 inches (0.500 ft), 198 ÷ 0.500 = 396 sq ft.
Coverage of 11 tons at different depths
| Depth | Square feet covered | Square yards |
|---|---|---|
| 4 in | 594 | 66 |
| 6 in | 396 | 44 |
| 8 in | 297 | 33 |
About road base
Road base is meant to be compacted at close to the right moisture. Dry base rock does not lock up well; a light spray of water before rolling helps. Weight runs about 1.4 to 1.65 compacted tons per cubic yard, so treat the table as a planning range rather than an exact figure.
Putting 11 tons to use
11 tons is about one tandem-axle truck load, though legal limits vary by truck and state. Spread from the pile with a loader, skid steer or wheelbarrow, then rake to depth before compacting if the material calls for it.
- Check depth as you go. Stakes marked at the target depth help keep the spread even.
- Expect some loss. Compaction and uneven ground use more than the flat-math figure. Keep about 10 percent in reserve.
- Ask about moisture. Wet material weighs more, so a ton of it covers less.
To run your own numbers, use the volume and tonnage calculator.
Where road base fits
Works well for:
- Base under asphalt and concrete
- Gravel roads and drives
- Equipment and shed pads
Poor fit for:
- Drainage layers
- Decorative surfaces
- Surfaces that will stay uncompacted
Quick reference numbers
- Per inch over 100 sq ft: about 0.46 tons of road base (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.6 tons.
- Another size for comparison: a 12x24 area at 4 inches takes about 5.3 tons.
- Weight used here: about 1.5 tons per cubic yard.
Mistakes that throw off the order
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
Questions people ask
How many cubic yards is 11 tons of road base?
About 7.3 cubic yards at 1.5 tons per yard.
How many square feet does 11 tons of road base cover at 6 inches?
About 396 square feet.
How many square feet does 11 tons cover at 4 inches?
About 594 square feet.
How much does a yard of road base weigh?
About 1.4 to 1.65 compacted tons.
Will 11 tons fit in one truck?
It depends on the truck. Single-axle dump trucks often carry under 10 tons and tandems around 13 to 16; your supplier will know their limits.
Related guides
- Crushed Stone vs Gravel: Differences and Best Uses
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does 9 Tons of Road Base Cover?
- How Much Does 10 Tons of Road Base Cover?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.