How Much Does 12 Tons of Decomposed Granite Cover?
How much does 12 tons of decomposed granite cover depends on how deep you spread it. At about 1.35 tons per cubic yard, 12 tons is roughly 8.9 cubic yards. Spread 3 inches deep, that covers about 960 square feet. Go thinner and it covers more; go deeper and it covers less.
Volume and tonnage calculator →How the coverage is figured
- Tons to cubic yards: 12 ÷ 1.35 = 8.9 yd³.
- Cubic yards to cubic feet: × 27 = 240 cu ft.
- Divide by depth in feet: at 3 inches (0.250 ft), 240 ÷ 0.250 = 960 sq ft.
Coverage of 12 tons at different depths
| Depth | Square feet covered | Square yards |
|---|---|---|
| 2 in | 1,440 | 160 |
| 3 in | 960 | 107 |
| 4 in | 720 | 80 |
About decomposed granite
DG should be laid in thin lifts, wetted and compacted. Loose DG at a deep depth stays soft and tracks onto shoes. Weight runs about 1.25 to 1.45 tons per cubic yard, so treat the table as a planning range rather than an exact figure.
Putting 12 tons to use
12 tons is about one tandem-axle truck load, though legal limits vary by truck and state. Spread from the pile with a loader, skid steer or wheelbarrow, then rake to depth before compacting if the material calls for it.
- Check depth as you go. Stakes marked at the target depth help keep the spread even.
- Expect some loss. Compaction and uneven ground use more than the flat-math figure. Keep about 10 percent in reserve.
- Ask about moisture. Wet material weighs more, so a ton of it covers less.
To run your own numbers, use the volume and tonnage calculator.
Where decomposed granite fits
Good uses:
- Garden paths and patios with a natural look
- Around trees and in xeriscape designs
- Stabilized DG for accessible paths
Think twice for:
- Steep grades without a stabilizer
- Areas right outside doors, since fines track in
- Driveways with heavy turning traffic
Quick reference numbers
- Per inch over 100 sq ft: about 0.42 tons of decomposed granite (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.2 tons.
- Another size for comparison: a 10x20 area at 2 inches takes about 1.7 tons.
- Weight used here: about 1.35 tons per cubic yard.
Common estimating mistakes
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
Questions people ask
How many cubic yards is 12 tons of decomposed granite?
About 8.9 cubic yards at 1.35 tons per yard.
How many square feet does 12 tons of decomposed granite cover at 3 inches?
About 960 square feet.
How many square feet does 12 tons cover at 2 inches?
About 1,440 square feet.
How much does a yard of decomposed granite weigh?
About 1.25 to 1.45 tons.
Will 12 tons fit in one truck?
It depends on the truck. Single-axle dump trucks often carry under 10 tons and tandems around 13 to 16; your supplier will know their limits.
Related guides
- Crushed Stone vs Gravel: Differences and Best Uses
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does 10 Tons of Decomposed Granite Cover?
- How Much Does 11 Tons of Decomposed Granite Cover?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.