How Much Does 4 Tons of Decomposed Granite Cover?
How much does 4 tons of decomposed granite cover depends on how deep you spread it. At about 1.35 tons per cubic yard, 4 tons is roughly 3.0 cubic yards. Spread 3 inches deep, that covers about 320 square feet. Go thinner and it covers more; go deeper and it covers less.
Volume and tonnage calculator →How the coverage is figured
- Tons to cubic yards: 4 ÷ 1.35 = 3.0 yd³.
- Cubic yards to cubic feet: × 27 = 80 cu ft.
- Divide by depth in feet: at 3 inches (0.250 ft), 80 ÷ 0.250 = 320 sq ft.
Coverage of 4 tons at different depths
| Depth | Square feet covered | Square yards |
|---|---|---|
| 2 in | 480 | 53 |
| 3 in | 320 | 36 |
| 4 in | 240 | 27 |
About decomposed granite
Decomposed granite (DG) is weathered granite broken into small particles and fines. It packs into a firm, natural-looking path surface, and stabilized versions include a binder. Weight runs about 1.25 to 1.45 tons per cubic yard, so treat the table as a planning range rather than an exact figure.
Planning around 4 tons
For delivery, 4 tons usually fits on one smaller dump truck. Ask the supplier how they will split it. Spread from the pile with a loader, skid steer or wheelbarrow, then rake to depth before compacting if the material calls for it.
- Check depth as you go. Stakes marked at the target depth help keep the spread even.
- Expect some loss. Compaction and uneven ground use more than the flat-math figure. Keep about 10 percent in reserve.
- Ask about moisture. Wet material weighs more, so a ton of it covers less.
To run your own numbers, use the volume and tonnage calculator.
Where decomposed granite fits
Good uses:
- Garden paths and patios with a natural look
- Around trees and in xeriscape designs
- Stabilized DG for accessible paths
Less suited to:
- Steep grades without a stabilizer
- Areas right outside doors, since fines track in
- Driveways with heavy turning traffic
Quick reference numbers
- Per inch over 100 sq ft: about 0.42 tons of decomposed granite (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.2 tons.
- Another size for comparison: a 12x24 area at 2 inches takes about 2.4 tons.
- Weight used here: about 1.35 tons per cubic yard.
Mistakes that throw off the order
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
Questions people ask
How many cubic yards is 4 tons of decomposed granite?
About 3.0 cubic yards at 1.35 tons per yard.
How many square feet does 4 tons of decomposed granite cover at 3 inches?
About 320 square feet.
How many square feet does 4 tons cover at 2 inches?
About 480 square feet.
How much does a yard of decomposed granite weigh?
About 1.25 to 1.45 tons.
Will 4 tons fit in one truck?
It depends on the truck. Single-axle dump trucks often carry under 10 tons and tandems around 13 to 16; your supplier will know their limits.
Related guides
- Crushed Stone vs Gravel: Differences and Best Uses
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does 2 Tons of Decomposed Granite Cover?
- How Much Does 3 Tons of Decomposed Granite Cover?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.