How Much Does 13 Tons of Recycled Concrete Aggregate Cover?
How much does 13 tons of recycled concrete aggregate cover depends on how deep you spread it. At about 1.3 tons per cubic yard, 13 tons is roughly 10.0 cubic yards. Spread 4 inches deep, that covers about 810 square feet. Go thinner and it covers more; go deeper and it covers less.
Volume and tonnage calculator →How the coverage is figured
- Tons to cubic yards: 13 ÷ 1.3 = 10.0 yd³.
- Cubic yards to cubic feet: × 27 = 270 cu ft.
- Divide by depth in feet: at 4 inches (0.333 ft), 270 ÷ 0.333 = 810 sq ft.
Coverage of 13 tons at different depths
| Depth | Square feet covered | Square yards |
|---|---|---|
| 3 in | 1,080 | 120 |
| 4 in | 810 | 90 |
| 6 in | 540 | 60 |
About recycled concrete aggregate
Ask whether the recycled concrete has been screened for rebar and debris. Fresh-crushed concrete can also be alkaline, so keep it away from sensitive plantings and streams. Weight runs about 1.2 to 1.4 tons per cubic yard, so treat the table as a planning range rather than an exact figure.
Putting 13 tons to use
13 tons is about one tandem-axle truck load, though legal limits vary by truck and state. Spread from the pile with a loader, skid steer or wheelbarrow, then rake to depth before compacting if the material calls for it.
- Check depth as you go. Stakes marked at the target depth help keep the spread even.
- Expect some loss. Compaction and uneven ground use more than the flat-math figure. Keep about 10 percent in reserve.
- Ask about moisture. Wet material weighs more, so a ton of it covers less.
To run your own numbers, use the volume and tonnage calculator.
Good and poor uses for recycled concrete aggregate
Works well for:
- Driveway and pad bases
- Temporary construction entrances
- Fill under slabs when compacted in lifts
Think twice for:
- Near ponds, streams or sensitive plants, since fresh crush can raise pH
- Decorative top layers
- Drainage layers, unless the product is clean and screened
Quick reference numbers
- Per inch over 100 sq ft: about 0.40 tons of recycled concrete aggregate (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.0 tons.
- Another size for comparison: a 10x20 area at 2 inches takes about 1.6 tons.
- Weight used here: about 1.3 tons per cubic yard.
Mistakes that throw off the order
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
Questions people ask
How many cubic yards is 13 tons of recycled concrete aggregate?
About 10.0 cubic yards at 1.3 tons per yard.
How many square feet does 13 tons of recycled concrete aggregate cover at 4 inches?
About 810 square feet.
How many square feet does 13 tons cover at 3 inches?
About 1,080 square feet.
How much does a yard of recycled concrete aggregate weigh?
About 1.2 to 1.4 tons.
Will 13 tons fit in one truck?
It depends on the truck. Single-axle dump trucks often carry under 10 tons and tandems around 13 to 16; your supplier will know their limits.
Related guides
- Crushed Stone vs Gravel: Differences and Best Uses
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does 11 Tons of Recycled Concrete Aggregate Cover?
- How Much Does 12 Tons of Recycled Concrete Aggregate Cover?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.