How Much Does 2 Tons of #57 Stone Cover?
How much does 2 tons of #57 stone cover depends on how deep you spread it. At about 1.35 tons per cubic yard, 2 tons is roughly 1.5 cubic yards. Spread 4 inches deep, that covers about 120 square feet. Halve the depth and you roughly double the area.
Volume and tonnage calculator →How the coverage is figured
- Tons to cubic yards: 2 ÷ 1.35 = 1.5 yd³.
- Cubic yards to cubic feet: × 27 = 40 cu ft.
- Divide by depth in feet: at 4 inches (0.333 ft), 40 ÷ 0.333 = 120 sq ft.
Coverage of 2 tons at different depths
| Depth | Square feet covered | Square yards |
|---|---|---|
| 2 in | 240 | 27 |
| 3 in | 160 | 18 |
| 4 in | 120 | 13 |
| 6 in | 80 | 9 |
About #57 stone
#57 stone is a clean crushed stone in roughly the 1/2 to 1 inch range with very few fines. It drains fast, which suits drainage layers and the top of a gravel drive, but it does not pack into a hard crust by itself. Weight runs about 1.3 to 1.45 tons per cubic yard, so treat the table as a planning range rather than an exact figure.
Planning around 2 tons
2 tons is a light load that a single-axle dump truck can often handle, though legal limits vary by truck and state. Spread from the pile with a loader, skid steer or wheelbarrow, then rake to depth before compacting if the material calls for it.
- Check depth as you go. Stakes marked at the target depth help keep the spread even.
- Expect some loss. Compaction and uneven ground use more than the flat-math figure. Keep about 10 percent in reserve.
- Ask about moisture. Wet material weighs more, so a ton of it covers less.
To run your own numbers, use the volume and tonnage calculator.
When to choose #57 stone
Best suited to:
- French drains and drainage layers
- The top course of a gravel driveway
- Under sheds where water needs to drain away
Think twice for:
- A standalone base, since it does not pack hard without fines
- Paver setting beds
- Walk paths meant for strollers or wheelchairs
Quick reference numbers
- Per inch over 100 sq ft: about 0.42 tons of #57 stone (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.2 tons.
- Another size for comparison: a 10x20 area at 4 inches takes about 3.3 tons.
- Weight used here: about 1.35 tons per cubic yard.
Mistakes that throw off the order
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
Questions people ask
How many cubic yards is 2 tons of #57 stone?
About 1.5 cubic yards at 1.35 tons per yard.
How many square feet does 2 tons of #57 stone cover at 4 inches?
About 120 square feet.
How many square feet does 2 tons cover at 2 inches?
About 240 square feet.
How much does a yard of #57 stone weigh?
About 1.3 to 1.45 tons.
Will 2 tons fit in one truck?
It depends on the truck. Single-axle dump trucks often carry under 10 tons and tandems around 13 to 16; your supplier will know their limits.
Related guides
- Number 57 Stone: Size, Weight, Uses, and Coverage
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.