How Much Does 4 Tons of #57 Stone Cover?
How much does 4 tons of #57 stone cover depends on how deep you spread it. At about 1.35 tons per cubic yard, 4 tons is roughly 3.0 cubic yards. Spread 4 inches deep, that covers about 240 square feet. Halve the depth and you roughly double the area.
Volume and tonnage calculator →How the coverage is figured
- Tons to cubic yards: 4 ÷ 1.35 = 3.0 yd³.
- Cubic yards to cubic feet: × 27 = 80 cu ft.
- Divide by depth in feet: at 4 inches (0.333 ft), 80 ÷ 0.333 = 240 sq ft.
Coverage of 4 tons at different depths
| Depth | Square feet covered | Square yards |
|---|---|---|
| 2 in | 480 | 53 |
| 3 in | 320 | 36 |
| 4 in | 240 | 27 |
| 6 in | 160 | 18 |
About #57 stone
Since #57 is washed and open-graded, it moves a little underfoot. Many installers put it over a compacted base of a dense-graded stone rather than straight on soil. Weight runs about 1.3 to 1.45 tons per cubic yard, so treat the table as a planning range rather than an exact figure.
Planning around 4 tons
4 tons is a light load that a single-axle dump truck can often handle, though legal limits vary by truck and state. Spread from the pile with a loader, skid steer or wheelbarrow, then rake to depth before compacting if the material calls for it.
- Check depth as you go. Stakes marked at the target depth help keep the spread even.
- Expect some loss. Compaction and uneven ground use more than the flat-math figure. Keep about 10 percent in reserve.
- Ask about moisture. Wet material weighs more, so a ton of it covers less.
To run your own numbers, use the volume and tonnage calculator.
When to choose #57 stone
Works well for:
- French drains and drainage layers
- The top course of a gravel driveway
- Under sheds where water needs to drain away
Less suited to:
- A standalone base, since it does not pack hard without fines
- Paver setting beds
- Walk paths meant for strollers or wheelchairs
Quick reference numbers
- Per inch over 100 sq ft: about 0.42 tons of #57 stone (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.2 tons.
- Another size for comparison: a 10x20 area at 3 inches takes about 2.5 tons.
- Weight used here: about 1.35 tons per cubic yard.
Common estimating mistakes
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
Questions people ask
How many cubic yards is 4 tons of #57 stone?
About 3.0 cubic yards at 1.35 tons per yard.
How many square feet does 4 tons of #57 stone cover at 4 inches?
About 240 square feet.
How many square feet does 4 tons cover at 2 inches?
About 480 square feet.
How much does a yard of #57 stone weigh?
About 1.3 to 1.45 tons.
Will 4 tons fit in one truck?
It depends on the truck. Single-axle dump trucks often carry under 10 tons and tandems around 13 to 16; your supplier will know their limits.
Related guides
- Number 57 Stone: Size, Weight, Uses, and Coverage
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does 2 Tons of #57 Stone Cover?
- How Much Does 3 Tons of #57 Stone Cover?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.