How Much Does 23 Tons of Asphalt Millings Cover?
How much does 23 tons of asphalt millings cover depends on how deep you spread it. At about 1.3 tons per cubic yard, 23 tons is roughly 17.7 cubic yards. Spread 4 inches deep, that covers about 1,433 square feet. Every added inch of depth cuts the coverage noticeably.
Volume and tonnage calculator →How the coverage is figured
- Tons to cubic yards: 23 ÷ 1.3 = 17.7 yd³.
- Cubic yards to cubic feet: × 27 = 478 cu ft.
- Divide by depth in feet: at 4 inches (0.333 ft), 478 ÷ 0.333 = 1,433 sq ft.
Coverage of 23 tons at different depths
| Depth | Square feet covered | Square yards |
|---|---|---|
| 3 in | 1,911 | 212 |
| 4 in | 1,433 | 159 |
| 6 in | 955 | 106 |
About asphalt millings
Millings vary by source: some loads are fine and uniform, others carry chunks. Ask the supplier for a screened product if you want a smoother finish, and check local rules, since some areas restrict their use near water. Weight runs about 1.2 to 1.4 loose tons per cubic yard, so treat the table as a planning range rather than an exact figure.
Putting 23 tons to use
23 tons will usually take two or more truck loads, though legal limits vary by truck and state. Spread from the pile with a loader, skid steer or wheelbarrow, then rake to depth before compacting if the material calls for it.
- Check depth as you go. Stakes marked at the target depth help keep the spread even.
- Expect some loss. Compaction and uneven ground use more than the flat-math figure. Keep about 10 percent in reserve.
- Ask about moisture. Wet material weighs more, so a ton of it covers less.
To run your own numbers, use the volume and tonnage calculator.
Where asphalt millings fits
Works well for:
- Rural driveways and farm lanes
- Parking areas where a dust-free surface is wanted
- Low-cost base under a future paved surface
Poor fit for:
- Areas near wells or streams where local rules limit them
- Decorative or barefoot areas
- Jobs needing a uniform, clean look
Quick reference numbers
- Per inch over 100 sq ft: about 0.40 tons of asphalt millings (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.0 tons.
- Another size for comparison: a 14x28 area at 2 inches takes about 3.1 tons.
- Weight used here: about 1.3 tons per cubic yard.
Where estimates go wrong
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
Questions people ask
How many cubic yards is 23 tons of asphalt millings?
About 17.7 cubic yards at 1.3 tons per yard.
How many square feet does 23 tons of asphalt millings cover at 4 inches?
About 1,433 square feet.
How many square feet does 23 tons cover at 3 inches?
About 1,911 square feet.
How much does a yard of asphalt millings weigh?
About 1.2 to 1.4 loose tons.
Will 23 tons fit in one truck?
It depends on the truck. Single-axle dump trucks often carry under 10 tons and tandems around 13 to 16; your supplier will know their limits.
Related guides
- How Many Tons of Asphalt Millings for a 40x25 Area?
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does 21 Tons of Asphalt Millings Cover?
- How Much Does 22 Tons of Asphalt Millings Cover?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.