How Much Does 25 Tons of Recycled Concrete Aggregate Cover?
How much does 25 tons of recycled concrete aggregate cover depends on how deep you spread it. At about 1.3 tons per cubic yard, 25 tons is roughly 19.2 cubic yards. Spread 4 inches deep, that covers about 1,558 square feet. Every added inch of depth cuts the coverage noticeably.
Volume and tonnage calculator →How the coverage is figured
- Tons to cubic yards: 25 ÷ 1.3 = 19.2 yd³.
- Cubic yards to cubic feet: × 27 = 519 cu ft.
- Divide by depth in feet: at 4 inches (0.333 ft), 519 ÷ 0.333 = 1,558 sq ft.
Coverage of 25 tons at different depths
| Depth | Square feet covered | Square yards |
|---|---|---|
| 3 in | 2,077 | 231 |
| 4 in | 1,558 | 173 |
| 6 in | 1,038 | 115 |
About recycled concrete aggregate
Recycled concrete aggregate is crushed old concrete. It compacts well and often costs less than virgin stone, which makes it a common driveway and pad base. Weight runs about 1.2 to 1.4 tons per cubic yard, so treat the table as a planning range rather than an exact figure.
Planning around 25 tons
25 tons will usually take two or more truck loads, though legal limits vary by truck and state. Spread from the pile with a loader, skid steer or wheelbarrow, then rake to depth before compacting if the material calls for it.
- Check depth as you go. Stakes marked at the target depth help keep the spread even.
- Expect some loss. Compaction and uneven ground use more than the flat-math figure. Keep about 10 percent in reserve.
- Ask about moisture. Wet material weighs more, so a ton of it covers less.
To run your own numbers, use the volume and tonnage calculator.
Good and poor uses for recycled concrete aggregate
Works well for:
- Driveway and pad bases
- Temporary construction entrances
- Fill under slabs when compacted in lifts
Think twice for:
- Near ponds, streams or sensitive plants, since fresh crush can raise pH
- Decorative top layers
- Drainage layers, unless the product is clean and screened
Quick reference numbers
- Per inch over 100 sq ft: about 0.40 tons of recycled concrete aggregate (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.0 tons.
- Another size for comparison: a 14x28 area at 2 inches takes about 3.1 tons.
- Weight used here: about 1.3 tons per cubic yard.
Mistakes that throw off the order
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
Questions people ask
How many cubic yards is 25 tons of recycled concrete aggregate?
About 19.2 cubic yards at 1.3 tons per yard.
How many square feet does 25 tons of recycled concrete aggregate cover at 4 inches?
About 1,558 square feet.
How many square feet does 25 tons cover at 3 inches?
About 2,077 square feet.
How much does a yard of recycled concrete aggregate weigh?
About 1.2 to 1.4 tons.
Will 25 tons fit in one truck?
It depends on the truck. Single-axle dump trucks often carry under 10 tons and tandems around 13 to 16; your supplier will know their limits.
Related guides
- Crushed Stone vs Gravel: Differences and Best Uses
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does 23 Tons of Recycled Concrete Aggregate Cover?
- How Much Does 24 Tons of Recycled Concrete Aggregate Cover?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.