How Much Does 29 Tons of Pea Gravel Cover?
How much does 29 tons of pea gravel cover depends on how deep you spread it. At about 1.4 tons per cubic yard, 29 tons is roughly 20.7 cubic yards. Spread 3 inches deep, that covers about 2,237 square feet. Halve the depth and you roughly double the area.
Volume and tonnage calculator →How the coverage is figured
- Tons to cubic yards: 29 ÷ 1.4 = 20.7 yd³.
- Cubic yards to cubic feet: × 27 = 559 cu ft.
- Divide by depth in feet: at 3 inches (0.250 ft), 559 ÷ 0.250 = 2,237 sq ft.
Coverage of 29 tons at different depths
| Depth | Square feet covered | Square yards |
|---|---|---|
| 2 in | 3,356 | 373 |
| 3 in | 2,237 | 249 |
| 4 in | 1,678 | 186 |
About pea gravel
Because pea gravel is round, it never fully locks. Keep depths modest on walkways and patios so it does not feel like walking on a beach, and use edging. Weight runs about 1.3 to 1.5 tons per cubic yard, so treat the table as a planning range rather than an exact figure.
Planning around 29 tons
For delivery, 29 tons means multiple trips or a larger truck. Ask the supplier how they will split it. Spread from the pile with a loader, skid steer or wheelbarrow, then rake to depth before compacting if the material calls for it.
- Check depth as you go. Stakes marked at the target depth help keep the spread even.
- Expect some loss. Compaction and uneven ground use more than the flat-math figure. Keep about 10 percent in reserve.
- Ask about moisture. Wet material weighs more, so a ton of it covers less.
To run your own numbers, use the volume and tonnage calculator.
When to choose pea gravel
Good uses:
- Patios, walkways and dog runs
- Play areas with proper depth and edging
- Drainage around foundations when sized properly
Poor fit for:
- Driveways and steep paths, where it rolls and ruts
- Under pavers as a base
- Areas without edging
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of pea gravel (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 10x20 area at 3 inches takes about 2.6 tons.
- Weight used here: about 1.4 tons per cubic yard.
Common estimating mistakes
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
Questions people ask
How many cubic yards is 29 tons of pea gravel?
About 20.7 cubic yards at 1.4 tons per yard.
How many square feet does 29 tons of pea gravel cover at 3 inches?
About 2,237 square feet.
How many square feet does 29 tons cover at 2 inches?
About 3,356 square feet.
How much does a yard of pea gravel weigh?
About 1.3 to 1.5 tons.
Will 29 tons fit in one truck?
It depends on the truck. Single-axle dump trucks often carry under 10 tons and tandems around 13 to 16; your supplier will know their limits.
Related guides
- How Much Does a Ton of Gravel Cover? Depth Chart
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does 27 Tons of Pea Gravel Cover?
- How Much Does 28 Tons of Pea Gravel Cover?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.