How Much Limestone Screenings for a 6x30 Walkway?
How much limestone screenings for a 6x30 walkway: at 3 inches deep you need about 1.67 cubic yards, which is roughly 2.3 tons at 1.4 tons per yard. The walkway covers 180 square feet, so every inch of depth adds about 0.56 yards.
Volume and tonnage calculator →The math for a 6x30 walkway
- Area: 6 × 30 = 180 sq ft.
- Depth in feet: 3 ÷ 12 = 0.250 ft.
- Cubic feet: 180 × 0.250 = 45.0 cu ft.
- Cubic yards: ÷ 27 = 1.67 yd³.
- Tons: × 1.4 = 2.3 tons.
The volume and tonnage calculator does this for any size.
Limestone screenings needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 1 in | 0.56 | 0.8 | 0.9 |
| 2 in | 1.11 | 1.6 | 1.7 |
| 3 in | 1.67 | 2.3 | 2.6 |
About limestone screenings
Limestone screenings are the fine dust and chips left after crushing limestone. They pack very tight, which makes them a common setting bed for pavers and flagstone and a surface for paths. If the yard sells by the cubic yard instead of the ton, use the cubic-yard column directly.
Preparing the walkway
Dig the path a few inches below grade, compact the bottom, add fabric if needed and install edging on both sides so the material stays on the walk. For foot traffic, the depths in the table above are a reasonable starting range.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 2.6 tons fits in a single typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the walkway as firm ground allows.
Where limestone screenings fits
Best suited to:
- Paver and flagstone setting beds
- Firm walking paths
- Top-dressing a compacted stone base
Think twice for:
- Deep layers on their own
- Low spots that collect water
- Under heavy vehicle traffic without a base
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of limestone screenings (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 8x16 area at 3 inches takes about 1.7 tons.
- Weight used here: about 1.4 tons per cubic yard.
Common estimating mistakes
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
Questions people ask
How many tons of limestone screenings for a 6x30 walkway?
About 2.3 tons at 3 inches deep, or 2.6 tons with 10 percent extra.
How many cubic yards is a 6x30 walkway at 3 inches?
About 1.67 cubic yards.
How much does a cubic yard of limestone screenings weigh?
Usually around 1.3 to 1.5 tons, depending on stone size, fines and moisture.
How deep should limestone screenings be for a walkway?
The table above shows 1 to 3 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 6x30?
180 square feet.
Related guides
- #10 Stone (Stone Dust): Size, Uses and How Many Tons
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much Limestone Screenings for a 6x20 Walkway?
- How Much Limestone Screenings for a 6x25 Walkway?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.