How Much Pea Gravel for a 6x100 Walkway?
How much pea gravel for a 6x100 walkway: at 3 inches deep you need about 5.56 cubic yards, which is roughly 7.8 tons at 1.4 tons per yard. The walkway covers 600 square feet, so every inch of depth adds about 1.85 yards.
Volume and tonnage calculator →The math for a 6x100 walkway
- Area: 6 × 100 = 600 sq ft.
- Depth in feet: 3 ÷ 12 = 0.250 ft.
- Cubic feet: 600 × 0.250 = 150.0 cu ft.
- Cubic yards: ÷ 27 = 5.56 yd³.
- Tons: × 1.4 = 7.8 tons.
The volume and tonnage calculator does this for any size.
Pea gravel needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 2 in | 3.70 | 5.2 | 5.7 |
| 3 in | 5.56 | 7.8 | 8.6 |
| 4 in | 7.41 | 10.4 | 11.4 |
About pea gravel
Because pea gravel is round, it never fully locks. Keep depths modest on walkways and patios so it does not feel like walking on a beach, and use edging. Weight per yard is a planning number; the scale ticket at the yard is the real one.
Preparing the walkway
Dig the path a few inches below grade, compact the bottom, add fabric if needed and install edging on both sides so the material stays on the walk. This walkway sees foot traffic, so match the depth to that load rather than to the minimum.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 8.6 tons fits in a single typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the walkway as firm ground allows.
Where pea gravel fits
Works well for:
- Patios, walkways and dog runs
- Play areas with proper depth and edging
- Drainage around foundations when sized properly
Less suited to:
- Driveways and steep paths, where it rolls and ruts
- Under pavers as a base
- Areas without edging
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of pea gravel (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 10x20 area at 4 inches takes about 3.5 tons.
- Weight used here: about 1.4 tons per cubic yard.
Where estimates go wrong
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
Questions people ask
How many tons of pea gravel for a 6x100 walkway?
About 7.8 tons at 3 inches deep, or 8.6 tons with 10 percent extra.
How many cubic yards is a 6x100 walkway at 3 inches?
About 5.56 cubic yards.
How much does a cubic yard of pea gravel weigh?
Usually around 1.3 to 1.5 tons, depending on stone size, fines and moisture.
How deep should pea gravel be for a walkway?
The table above shows 2 to 4 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 6x100?
600 square feet.
Related guides
- How Much Does a Ton of Gravel Cover? Depth Chart
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Pea Gravel for a 6x60 Walkway?
- How Much Pea Gravel for a 6x75 Walkway?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.