How Much River Rock for a 5x10 Walkway?
How much river rock for a 5x10 walkway: at 3 inches deep you need about 0.46 cubic yards, which is roughly 0.6 tons at 1.35 tons per yard. The walkway covers 50 square feet, so every inch of depth adds about 0.15 yards.
Volume and tonnage calculator →The math for a 5x10 walkway
- Area: 5 × 10 = 50 sq ft.
- Depth in feet: 3 ÷ 12 = 0.250 ft.
- Cubic feet: 50 × 0.250 = 12.5 cu ft.
- Cubic yards: ÷ 27 = 0.46 yd³.
- Tons: × 1.35 = 0.6 tons.
The volume and tonnage calculator does this for any size.
River rock needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 2 in | 0.31 | 0.4 | 0.5 |
| 3 in | 0.46 | 0.6 | 0.7 |
| 4 in | 0.62 | 0.8 | 0.9 |
About river rock
River rock is smooth, water-worn stone sold in sizes from about 3/4 inch to several inches. Larger sizes cover fewer square feet per ton at the same depth because the voids between stones are bigger. Weight per yard is a planning number; the scale ticket at the yard is the real one.
Preparing the walkway
Dig the path a few inches below grade, compact the bottom, add fabric if needed and install edging on both sides so the material stays on the walk. Since the walkway carries foot traffic, a little extra depth is cheap insurance.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 0.7 tons fits in a single typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At about 0.6 tons this job is small enough that bagged material could work; a 0.5 cubic foot bag holds about 1/54 of a yard, so compare the bag count with a bulk minimum.
- Where it drops. Have the truck dump as close to the walkway as firm ground allows.
Good and poor uses for river rock
Good uses:
- Dry creek beds and drainage swales
- Decorative borders and planting beds
- Around downspouts to stop splash erosion
Less suited to:
- Walking surfaces
- Driveways
- Bases under slabs or pavers
Quick reference numbers
- Per inch over 100 sq ft: about 0.42 tons of river rock (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.2 tons.
- Another size for comparison: a 8x16 area at 2 inches takes about 1.1 tons.
- Weight used here: about 1.35 tons per cubic yard.
Where estimates go wrong
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
Questions people ask
How many tons of river rock for a 5x10 walkway?
About 0.6 tons at 3 inches deep, or 0.7 tons with 10 percent extra.
How many cubic yards is a 5x10 walkway at 3 inches?
About 0.46 cubic yards.
How much does a cubic yard of river rock weigh?
Usually around 1.25 to 1.45 tons, depending on stone size, fines and moisture.
How deep should river rock be for a walkway?
The table above shows 2 to 4 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 5x10?
50 square feet.
Related guides
- How Much Does a Ton of River Rock Cover?
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much River Rock for a 4x75 Walkway?
- How Much River Rock for a 4x100 Walkway?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.