How Much Does 15 Tons of Limestone Screenings Cover?
How much does 15 tons of limestone screenings cover depends on how deep you spread it. At about 1.4 tons per cubic yard, 15 tons is roughly 10.7 cubic yards. Spread 2 inches deep, that covers about 1,736 square feet. Every added inch of depth cuts the coverage noticeably.
Volume and tonnage calculator →How the coverage is figured
- Tons to cubic yards: 15 ÷ 1.4 = 10.7 yd³.
- Cubic yards to cubic feet: × 27 = 289 cu ft.
- Divide by depth in feet: at 2 inches (0.167 ft), 289 ÷ 0.167 = 1,736 sq ft.
Coverage of 15 tons at different depths
| Depth | Square feet covered | Square yards |
|---|---|---|
| 1 in | 3,471 | 386 |
| 2 in | 1,736 | 193 |
| 3 in | 1,157 | 129 |
About limestone screenings
Screenings hold moisture and can crust over. Use them in thin layers over a compacted stone base instead of as a thick layer on their own. Weight runs about 1.3 to 1.5 tons per cubic yard, so treat the table as a planning range rather than an exact figure.
Planning around 15 tons
For delivery, 15 tons is in the range of one full tandem load. Ask the supplier how they will split it. Spread from the pile with a loader, skid steer or wheelbarrow, then rake to depth before compacting if the material calls for it.
- Check depth as you go. Stakes marked at the target depth help keep the spread even.
- Expect some loss. Compaction and uneven ground use more than the flat-math figure. Keep about 10 percent in reserve.
- Ask about moisture. Wet material weighs more, so a ton of it covers less.
To run your own numbers, use the volume and tonnage calculator.
When to choose limestone screenings
Works well for:
- Paver and flagstone setting beds
- Firm walking paths
- Top-dressing a compacted stone base
Less suited to:
- Deep layers on their own
- Low spots that collect water
- Under heavy vehicle traffic without a base
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of limestone screenings (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 8x16 area at 2 inches takes about 1.1 tons.
- Weight used here: about 1.4 tons per cubic yard.
Where estimates go wrong
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
Questions people ask
How many cubic yards is 15 tons of limestone screenings?
About 10.7 cubic yards at 1.4 tons per yard.
How many square feet does 15 tons of limestone screenings cover at 2 inches?
About 1,736 square feet.
How many square feet does 15 tons cover at 1 inches?
About 3,471 square feet.
How much does a yard of limestone screenings weigh?
About 1.3 to 1.5 tons.
Will 15 tons fit in one truck?
It depends on the truck. Single-axle dump trucks often carry under 10 tons and tandems around 13 to 16; your supplier will know their limits.
Related guides
- #10 Stone (Stone Dust): Size, Uses and How Many Tons
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does 13 Tons of Limestone Screenings Cover?
- How Much Does 14 Tons of Limestone Screenings Cover?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.