Tons of Asphalt Millings per Mile of 16 ft Road
Tons of asphalt millings per mile of 16 foot road: about 1,356 tons at 4 inches deep. The strip is 16 ft × 5,280 ft = 84,480 square feet. On a job this long, half an inch of extra depth adds a lot of tons.
Volume and tonnage calculator →Tons by depth
| Depth | Tons | Truckloads (~14 t) |
|---|---|---|
| 3 in | 1,017 | 73 |
| 4 in | 1,356 | 97 |
| 6 in | 2,034 | 146 |
| 8 in | 2,712 | 194 |
The math
- Area: 16 × 5,280 = 84,480 sq ft.
- Volume at 4 in: 84,480 × 0.333 = 28,160 cu ft (1,043 cubic yards).
- × 1.3 tons per yard = 1,356 tons.
What goes into the section
At 16 feet wide, two cars can meet with care. Asphalt millings are ground-up old pavement. When compacted and warmed by sun they bind into a fairly firm surface, which is why they are popular for rural drives and lots. Crown the surface so water sheds to ditches on both sides.
Practical notes
- Phasing. Large tonnages are delivered over days; schedule spreading and compaction to keep up with trucks.
- Waste. Allow 5 to 10 percent.
- Hauling. Distance from the quarry or plant often costs as much as the material on long jobs; see asphalt hauling cost per ton.
Check other sizes with the volume and tonnage calculator.
Good and poor uses for asphalt millings
Best suited to:
- Rural driveways and farm lanes
- Parking areas where a dust-free surface is wanted
- Low-cost base under a future paved surface
Think twice for:
- Areas near wells or streams where local rules limit them
- Decorative or barefoot areas
- Jobs needing a uniform, clean look
Quick reference numbers
- Per inch over 100 sq ft: about 0.40 tons of asphalt millings (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.0 tons.
- Another size for comparison: a 20x25 area at 4 inches takes about 8.0 tons.
- Weight used here: about 1.3 tons per cubic yard.
Common estimating mistakes
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
Questions people ask
How many tons of asphalt millings per mile of 16 ft road?
About 1,356 tons at 4 inches.
How many truckloads is that?
About 97 loads at roughly 14 tons each.
How many square feet is mile of 16 ft road?
84,480 square feet.
Should I add extra for waste?
Yes, 5 to 10 percent is common.
Does this include the shoulders?
No. Measure shoulders and pullouts separately and add them.
Related guides
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- Asphalt Hauling Cost Per Ton: What Drives the Delivered Price
- Crushed Stone vs Gravel: Differences and Best Uses
- Tons of Asphalt Millings per Mile of 14 ft Road
- Tons of Asphalt Millings per 100 Feet of 14 ft Road
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.