Tons of Crusher Run per Mile of 14 ft Road
Tons of crusher run per mile of 14 foot road: about 2,122 tons at 6 inches deep. The strip is 14 ft × 5,280 ft = 73,920 square feet. Shoulders, pullouts and turnarounds add to the total; measure them separately.
Volume and tonnage calculator →Tons by depth
| Depth | Tons | Truckloads (~14 t) |
|---|---|---|
| 3 in | 1,061 | 76 |
| 4 in | 1,415 | 102 |
| 6 in | 2,122 | 152 |
| 8 in | 2,829 | 203 |
The math
- Area: 14 × 5,280 = 73,920 sq ft.
- Volume at 6 in: 73,920 × 0.500 = 36,960 cu ft (1,369 cubic yards).
- × 1.55 tons per yard = 2,122 tons.
What goes into the section
At 14 feet wide, this is a single-lane private road or farm lane. Crusher run (also sold as crush and run, dense-grade aggregate or QP in some regions) mixes stone with stone dust. It compacts into a firm, nearly solid layer, which makes it the usual base under pavers, asphalt and gravel drives. Crown the surface so water sheds to ditches on both sides.
Practical notes
- Phasing. Large tonnages are delivered over days; schedule spreading and compaction to keep up with trucks.
- Waste. Allow 5 to 10 percent.
- Hauling. Distance from the quarry or plant often costs as much as the material on long jobs; see asphalt hauling cost per ton.
Check other sizes with the volume and tonnage calculator.
Good and poor uses for crusher run
Best suited to:
- Base under asphalt, pavers or concrete
- Gravel drives that need a firm, packed surface
- Shed pads and equipment pads
Poor fit for:
- Drainage layers, since the fines slow water
- Decorative beds
- Spots where you want water to soak straight through
Quick reference numbers
- Per inch over 100 sq ft: about 0.48 tons of crusher run (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.8 tons.
- Another size for comparison: a 14x28 area at 3 inches takes about 5.6 tons.
- Weight used here: about 1.55 tons per cubic yard.
Common estimating mistakes
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
Questions people ask
How many tons of crusher run per mile of 14 ft road?
About 2,122 tons at 6 inches.
How many truckloads is that?
About 152 loads at roughly 14 tons each.
How many square feet is mile of 14 ft road?
73,920 square feet.
Should I add extra for waste?
Yes, 5 to 10 percent is common.
Does this include the shoulders?
No. Measure shoulders and pullouts separately and add them.
Related guides
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- Asphalt Hauling Cost Per Ton: What Drives the Delivered Price
- Crushed Stone vs Gravel: Differences and Best Uses
- Tons of Crusher Run per Mile of 12 ft Road
- Tons of Crusher Run per 100 Feet of 12 ft Road
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.